carb leaking

Farmall Cub Forum -- Questions and answers to all of your Cub related issues.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.

carb leaking

Postby BOB K. » Thu Feb 19, 2004 9:51 am

I have 2 IH carbs. I have rebuild both of them but still leaking fuel. I ordered the Kolher needle valve that I was tood would fix the problem. But it is to tall . The float wll not fit on the carb with that part. what do I do? :?
BOB K.
10+ Years
10+ Years
 
Posts: 337
Joined: Sun Feb 02, 2003 10:34 pm
Location: Long Island, NY

Postby Bigdog » Thu Feb 19, 2004 10:14 am

Bob, Check this link to the FAQ page 7. It has both the piston ring numers and the Kohler needle valve number along with other valuable part cross references.
http://www.atis.net/CubFAQ/cub_faq.html#q7
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.

My wife says I don't listen to her. - - - - - - - - Or something like that!

http://www.cubtug.com
User avatar
Bigdog
Team Cub
Team Cub
 
Posts: 23820
Joined: Sun Feb 02, 2003 12:50 pm
Location: OH, Stoutsville
Zip Code: 43154
Circle of Safety Award
Circle of Safety: Y

Postby Lurker Carl » Thu Feb 19, 2004 10:27 am

I have been battling this as well. The Viton tipped needle didn't stop the leak. I think it's coming in around the threaded portion of the cage or the threaded portion of the main fuel nozzle. Both areas are submerged in fuel and the seats where the gasket sit are a bit rough.

I'm going to play around with thread sealants, compressed air and soapy water to chase down this gremlin.
User avatar
Lurker Carl
Team Cub Mentor
Team Cub Mentor
 
Posts: 3942
Joined: Mon Feb 03, 2003 9:54 am
Location: PA, Todd
Zip Code: 16685
Circle of Safety Award
Circle of Safety: Y

Postby George Willer » Thu Feb 19, 2004 11:12 am

Lurker Carl wrote:I have been battling this as well. The Viton tipped needle didn't stop the leak. I think it's coming in around the threaded portion of the cage or the threaded portion of the main fuel nozzle. Both areas are submerged in fuel and the seats where the gasket sit are a bit rough.

I'm going to play around with thread sealants, compressed air and soapy water to chase down this gremlin.


Carl,

I'm glad someone is finally following through with the suggestion. A very small amount of sealant applied with a toothpick will work wonders. I don't know of a way to check the fuel nozzle for leakage, but the test of the seat washer was dramatic proof of where the common problem really lies. I use sealer on both sides of both washers to be sure.

I've been having trouble with the viton needles sticking, so I'm back to using the originals.

Hint: Use one pound of pressure or less. The soapy water is in a squirt bottle.

Image
George Willer
http://gwill.net

The most affectionate creature in the world is a wet dog. Ambrose Bierce
User avatar
George Willer
Cub Pro
Cub Pro
 
Posts: 7011
Joined: Sun Feb 02, 2003 9:36 pm
Location: OHIO, Fremont
Zip Code: 43420
Circle of Safety Award
Circle of Safety: Y

Postby Lurker Carl » Thu Feb 19, 2004 11:37 am

George,

I did something very similar about 30 years ago to find why my Rochester 4GC was always flooding on the secondary side. After replacing the needle and cage several times, it was apparent that the needle was not the problem. It was the cage gasket leaking because the seat was gouged. Then I applied the same theory to a fuel dripping Marvel-Schebler on a Massey-Harris and it worked there as well.

Just like with the MH, I think the cage is the culprit here since it remains under pressure from the fuel load in the tank. With my first test, I used teflon tape on the Cub, but that didn't work. I'm going to try Permatex next. The fuel nozzle is not subjected to pressure so I'll check the fuel nozzle by filling the fuel bowl up to the top and seeing if anything seeps past the gasket over time.

I'll keep y'all informed.

LC
User avatar
Lurker Carl
Team Cub Mentor
Team Cub Mentor
 
Posts: 3942
Joined: Mon Feb 03, 2003 9:54 am
Location: PA, Todd
Zip Code: 16685
Circle of Safety Award
Circle of Safety: Y

Postby Donny M » Thu Feb 19, 2004 12:41 pm

While pressure testing thousands of aluminum dipoles in the field, we used soapy water. Big mistake...Soap is very corrosive and unless the parts are rinsed throughly the aluminum will corrode. White powder everwhere. :oops: :oops: :oops: Since then I use a product called Snoop, it's a noncorrosive leak detector.

Like a brass wire wheel on aluminum, Snoop is my preference for leak detection.
Donny M
5+ Years
5+ Years
 

Postby Jack Donovan » Thu Feb 19, 2004 5:25 pm

:idea: I certinly agree with Donnie about the soap' When I was in school in wood shop after predrilling a hole the teacher had us use a little soap on the screw and that made it turn easer and helped from splitting hard woods. so I remembered that when remoldeling my Kitchen cubords and cense have had to replace all the hinge screws. I don't know if it's the modern day soap or what but I just couldn't believe it. :shock: :shock:
Jack Donovan
10+ Years
10+ Years
 
Posts: 874
Joined: Sun Feb 02, 2003 11:19 pm

Postby Bill » Thu Feb 19, 2004 5:25 pm

WE USED SNOOP TO CHECK NATUARL GAS JOINTS FOR THE THIRTY PLUS YEARS AT MY JOB. ONLY OUNCES OF PRESURE. IF THERE IS A LEAK IT WILL SHOW. IT IS AMAZING HOW LONG A BOTTLE WILL LAST.
BILL
Bill
10+ Years
10+ Years
 
Posts: 172
Joined: Mon Feb 03, 2003 8:28 pm
Location: FREMONT OHIO
Zip Code: 43420


Return to Farmall Cub

Who is online

Users browsing this forum: Grandfather's Cub, jpcubs, Mr E, Paul Van Benschoten, staninlowerAL and 9 guests