Page 1 of 1
First Pass
Posted: Fri Apr 02, 2004 9:04 pm
by Dennis H.
Well, after busting a few knuckles I got my belly mower on Ole '48. After throwing the belt a couple times and relealizing I had the wrong pulley on the PTO, I put the right one on and took off.
Question: The mower really bogged down when I started mowing, almost killed the engine. Had it about half throttle in first gear. Is there a trick to this? I was hoping to use Ole '48 to mow the pasture and ditches along the road but I don't know if she'll handle it. Mainly fescue that's about 6" tall and fairly thick right now.
The mower is a Sun Master Kub Kutter made in Olathe KS., 42" cut. Any suggestions? Thanks guys, you've helped more than you realize with my new toy, er, I mean tool. (the wife may be reading this).
Posted: Fri Apr 02, 2004 9:23 pm
by Bigdog
Good sharp blades will help. You might also try taking half a swath on the first pass until you get it down to a manageable length.
Re: First Pass
Posted: Fri Apr 02, 2004 10:19 pm
by Dennis
Dennis H. wrote:
The mower is a Sun Master Kub Kutter made in Olathe KS., 42" cut. Any suggestions? Thanks guys, you've helped more than you realize with my new toy, er, I mean tool. (the wife may be reading this).
Hey Dennis, I have a Sun Master Kub Kutter manual around some where, if you want it, send me your address off line and I'll find it and sent it to you. You're the first person I know that has one...
Re: First Pass
Posted: Fri Apr 02, 2004 10:31 pm
by Jim Becker
Dennis H. wrote:Had it about half throttle in first gear.
Push the throttle the rest of the way open.
Posted: Fri Apr 02, 2004 10:32 pm
by John *.?-!.* cub owner
dennis H, if your KUb Kutter has the same arrangemen of shields around the deck as a Woods, you cna remove all of them for heavy cutting. Wouldn't reccomend doing it when cutting around house, due to throwing debris it hits.
Posted: Fri Apr 02, 2004 11:47 pm
by Dennis H.
Thanks guys. I'll try it again on Sunday as my daughter is pre-enrolling at ESU tomorrow and my Sat. is pretty well tied up.
I did sharpen the blades prior to installing the mower. You wouldn't believe the amount of wire and bailing string I cleaned out that had wrapped around the shaft from years past.
What I did get cut looks a whole lot nicer than what the Craftsman cut. I think I'll give it to the wife.
Posted: Sat Apr 03, 2004 8:46 am
by Michael Az
You might want to check the level of the mower. If the front of the mower is higher than the rear, it will require twice the power to drive it. As the front of the mower passes over the grass it cuts then has to cut again as the rear passes over because it is in a lower position than the front. Anyway, thats how they work here in the sand.
Michael Az
Posted: Sat Apr 03, 2004 7:53 pm
by Ike
Dennis H.
I hope you enjoyed your day here in Emporia.
Ike
Posted: Sun Apr 04, 2004 8:01 am
by Dennis H.
Ike,
Glad to see another Kansan on here. We did enjoy the day in Emporia except for the fact that I didn't get to spend much time at Bluestem. This is the second daughter I'll have at ESU so I have twice the reasons now to go back.
Is there any way to change the height of cut at the back of the mower? When I head to the ditches I will want to keep it much higher as they are somewhat steep and not the smoothest.
Dennis (47 Cub), thanks so much for the offer. I sent you a pm with my address. The manual may answer my questions so I don't need to bug you guys with my rookie inquiries.