This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
A ? about J.B. Weld
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 202
- Joined: Fri Mar 07, 2003 8:17 pm
- Zip Code: 00000
- Tractors Owned: 52 Cub Fast Hitch 68 Lo-Boy 66 Cub Cadet 125 100 Manure Spreader Wagner Loader
- Circle of Safety: Y
- Location: Hunterdon County N.J.
A ? about J.B. Weld
This is slightly off topic but I think it could apply to Cubs as well. I want to repair the hood on my riding mower it is fiberglass and has hinges lagged to it on at the base of the hood. They are stripped out and I bought some JB Weld to repair the holes, I am going to use my dremel and oval out the holes so the cured J B Weld doesn't turn in the holes. My question is should I put the lags into the epoxy while it is wet or let it dry and drill it and screw them in, I figure if I clean them up real good the wet J B weld would probably bond to them pretty good as well as to the hood, Just wondering if anyone else has done this before. Thanks T.J.
Blue Mountain Antique Gas and Steam Engine Association
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
If you put them in wet, they'll probably end up being a permanent assembly. If you let it set up and then drill & tap, you will be able to dis-assemble if necessary.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
- John *.?-!.* cub owner
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
-
- 10+ Years
- Posts: 202
- Joined: Fri Mar 07, 2003 8:17 pm
- Zip Code: 00000
- Tractors Owned: 52 Cub Fast Hitch 68 Lo-Boy 66 Cub Cadet 125 100 Manure Spreader Wagner Loader
- Circle of Safety: Y
- Location: Hunterdon County N.J.
well I went to their web site to check on if it could be used on fiberglass, and they recomend it for fiberglass boat repairs. The lags that go into the hood are lag on the bottom and 1/4-20 studs on top, so If putting them in wet is stronger thats what I will do. I have never used this stuff before how thin is it once its mixed, like pancake batter or it is thicker , also how long do you have to work with it once it is mixed? Thanks for all the help so far, T.J.
Blue Mountain Antique Gas and Steam Engine Association
-
- Team Cub
- Posts: 17272
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Once it is mixed to an even color (no streaks) it is mixed. It is thicker than pancake batter but how thick depends a lot on what the temperature is. I would not describe it as runny, but it will sag if given the chance.
There are 2 versions of the material. The standard stuff gives you quite a bit of work time. If you use the fast version, you may want to mix the material for one stud at a time. In any case, have everything ready to go before you mix the JB.
There are 2 versions of the material. The standard stuff gives you quite a bit of work time. If you use the fast version, you may want to mix the material for one stud at a time. In any case, have everything ready to go before you mix the JB.
- Lurker Carl
- Cub Pro
- Posts: 3970
- Joined: Mon Feb 03, 2003 9:54 am
- Zip Code: 16685
- Circle of Safety: Y
- Location: PA, Todd
JB Weld will be like honey when you mix the components. Clean, clean, clean everything you want it to adhere to and don't touch these areas with fingers. You can use Playdough, plastic wrap and Al foil to help dam or contain the stuff where it needs to be. Depending on temperature and humidity, it will take from up to 6 hours for it to stiffen, lower temp and humidity = longer time. I have used auto wax on bolt threads to keep JB Weld from adhereing, although you will need to apply some force to the bolt to break the bond. It should hold lags if there is enough textured surface on the lag for the JB Weld to adhere to. Let it cure for 24 hours before you try to remove the bolts, otherwise the "weld" will be too soft and self destruct.
Good luck!
Good luck!
-
- 10+ Years
- Posts: 227
- Joined: Mon Feb 03, 2003 9:42 am
- Zip Code: 71303
- Tractors Owned: 1-69 Cub
5- Cub Cadets - Location: Alexandria, La.
Hinge repair
Welder,
Why don't you consider using Welnuts. Work quite well where you need a bit of movement between pieces, like those mounted in fiberglass.
They are rubber with brass nutplate inserts.
moe1942
Why don't you consider using Welnuts. Work quite well where you need a bit of movement between pieces, like those mounted in fiberglass.
They are rubber with brass nutplate inserts.
moe1942
Who is online
Users browsing this forum: No registered users and 35 guests