This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Cub starting problem - I'm stumped
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 9
- Joined: Wed May 26, 2004 7:17 am
- Location: Ontario
Cub starting problem - I'm stumped
I need help with my Cub! It wouldn't start, just turned over but no spark. It's a 1948 with 6 V positive ground. I checked the ignition switch and found that it was faulty, so being cheap I bought an ordinary push-pull switch to replace it. The new switch has two terminals rather then one terminal and a ground, so I ran a new wire from the second terminal of the switch back to the positive terminal of the battery. I tried it - nothing! Now it won't even turn over, even without the switch installed. What the heck could be going on?
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
Your old switch with one terminal was a kill switch or grounding switch for a magneto ignition system. The 2 terminal switch is for battery ignition systems. If you are trying to start the tractor with the switch pulled out it will never start because it is grounding the points. You can either leave the switch in the off (or in) position and start the tractor or replace it with the correct switch. Your 2 terminal switch operates backwards from the single terminal switch.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
- 10+ Years
- Posts: 9
- Joined: Wed May 26, 2004 7:17 am
- Location: Ontario
Thanks
Thanks for the quick answer. I see that part of the problem is that I am stupid. Oh, well. Hmm.. If the switch is open to start there must be something else wrong as well, since the old switch was showing open in both positions when I tested it, the tractor should have started. It used to start quite well, then all of a sudden one day it just wouldn't spark. Has anyone experienced that before?
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
You might want to open up the disrtibutor on the mag and check the points. Magneto systems are usually pretty reliable and sudden problems that crop up are easy to track down and fix. The kill switch wire may be shorting out somewhere. Try disconnecting it at the post on the side of the distributor and see if it will start. Pull the center wire on the distributor, hold it close to ground and crank the tractor over and see if you have spark. Check back and we'll work through this.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
- 10+ Years
- Posts: 9
- Joined: Wed May 26, 2004 7:17 am
- Location: Ontario
Finally I've had some time to work on the Cub. One problem was the battery would no longer charge - got a new one. Still won't start with the kill switch wire removed from the magneto. There is plenty of spark on the wire to the distributor. I was looking at the drive gear on the rotor and noticed it seemed fairly worn. Maybe it's not turning properly. I tried turning the engine over with the distributor cap off and the rotor was turning but it seemed pretty slow. I was surprised that the rotor and its drive gear are plastic!
- Carm
- 10+ Years
- Posts: 1085
- Joined: Thu Aug 28, 2003 2:11 pm
- Zip Code: 21234
- Tractors Owned: 1947 FCub 1948 FCub (FrankenCub), 1949 C, 1952 SA, 1963 IH 3414 Backhoe Diesel, 1960 Oliver 880 Diesel, 1945 Mack EF Fire Truck
- Circle of Safety: Y
- Location: MD, Baltimore and Freeland
- Contact:
I would verify that you are getting a spark at the plugs. Make sure you have the copper core wires as the resistance type can severely limit your spark. I had a similar problem. New wires helped. I then replaced the coil and now its great. The distributor will turn more slowly than the engine, that is normal. Make sure also, that you can hear the mag impulse coupling snap for each firing position. Verify the firing order as well.
Last edited by Carm on Fri Jun 25, 2004 8:33 am, edited 1 time in total.
-
- 10+ Years
- Posts: 9
- Joined: Wed May 26, 2004 7:17 am
- Location: Ontario
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
James:
I use the Canadian Tire Electronic cleaner - spray type. Some very fine sand paper - 220 or finer and just touch up the contacts.
Check the points for proper gap and the condensor. Condensor's don't usually go, but I had to replace Ellie's a little while ago.
Hey, welcome to the Forum!
I use the Canadian Tire Electronic cleaner - spray type. Some very fine sand paper - 220 or finer and just touch up the contacts.
Check the points for proper gap and the condensor. Condensor's don't usually go, but I had to replace Ellie's a little while ago.
Hey, welcome to the Forum!
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 111
- Joined: Wed Nov 19, 2003 10:54 pm
- Location: Roxbury, CT
Question on Ignition Switch Position for Battery vs Mag
Hi Big Dog
I read your reply on the position of the switch. I am a little confused now. I have a 48 cub with Mag ignition, and for this one, the switch is pulled-out to make her run.
Now, just last Saturday I picked up a beaten up old 61 cub with battery ignition. When I went to try and start it, I pulled the switch out (assuming it is the same as my other cub). But it didn't run. I also pulled the plugs and no spark. Thinking that the switch might be defective, I pulled the grounding wire off the distributor, but it still didn't start/spark.
Tomorrow I am going to replace points etc, but I guess I want to check about the switch position. Should it be pulled or pushed to run with the battery ignition? What about the grounding wire on the distributor? Should I remove it to take the switch out of the circuit (just like the mag ignition).
Thanks
I read your reply on the position of the switch. I am a little confused now. I have a 48 cub with Mag ignition, and for this one, the switch is pulled-out to make her run.
Now, just last Saturday I picked up a beaten up old 61 cub with battery ignition. When I went to try and start it, I pulled the switch out (assuming it is the same as my other cub). But it didn't run. I also pulled the plugs and no spark. Thinking that the switch might be defective, I pulled the grounding wire off the distributor, but it still didn't start/spark.
Tomorrow I am going to replace points etc, but I guess I want to check about the switch position. Should it be pulled or pushed to run with the battery ignition? What about the grounding wire on the distributor? Should I remove it to take the switch out of the circuit (just like the mag ignition).
Thanks
-
- 10+ Years
- Posts: 264
- Joined: Sat Nov 08, 2003 10:07 am
- Location: Missouri/Sullivan
- parts man
- 10+ Years
- Posts: 619
- Joined: Wed Jul 30, 2003 9:41 pm
- Location: Sussex N.B. Can.
- Contact:
David, the wire to a distributer is the power wire, it needs to be connected in order to get a spark. The switches both are supposed to be out in the run position, for a mag switch (one contact) that means its an open circuit, for a distributer switch (two contacts) it is a closed circuit.
Check to see that you are getting power to your coil with the switch pulled out.
Check to see that you are getting power to your coil with the switch pulled out.
V.P. of T.S.A. (taking stuff apart)
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
Re: Question on Ignition Switch Position for Battery vs Mag
David wrote:Hi Big Dog
I read your reply on the position of the switch. I am a little confused now. I have a 48 cub with Mag ignition, and for this one, the switch is pulled-out to make her run.
Now, just last Saturday I picked up a beaten up old 61 cub with battery ignition. When I went to try and start it, I pulled the switch out (assuming it is the same as my other cub). But it didn't run. I also pulled the plugs and no spark. Thinking that the switch might be defective, I pulled the grounding wire off the distributor, but it still didn't start/spark.
Tomorrow I am going to replace points etc, but I guess I want to check about the switch position. Should it be pulled or pushed to run with the battery ignition? What about the grounding wire on the distributor? Should I remove it to take the switch out of the circuit (just like the mag ignition).
Thanks
David, with the mag switch, in the out position, the switch contacts are open. With a standard 2 terminal switch, in the out position, the contacts are closed. The switch contacts must be open to run on a mag system.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
- 10+ Years
- Posts: 9
- Joined: Wed May 26, 2004 7:17 am
- Location: Ontario
Well, last weekend I checked the points, adjusted them a bit (they look to be in good shape), cleaned the distributor, put everything back together, and I was getting good spark at the plugs, but no startey!. I checked a plug after turning it over a few times, and noticed it was dry. My almost new Zenith carb must be plugged with crud. That was the first thing I thought of when it wouldn't start, so I took the carb off and blew it out with air, but it didn't help. I guess I'll have to take the carb apart and soak it in carburetor cleaner. Does anyone use a gas additive or use higher-octane gas to avoid this problem?
- LYNYRD
- 10+ Years
- Posts: 238
- Joined: Sat Mar 29, 2003 9:26 am
- Zip Code: 70453
- Tractors Owned: 1974 IH Cub
1975 IH Cub
MF 135
TO-20
Ford 3000
12 D Harrow Plow
151 Disc Plow - Circle of Safety: Y
- Location: LA, Pine Grove
Chem Tool
I use a product call Chem tool on one of my cubs that had not been used for approx. one year.
Who is online
Users browsing this forum: No registered users and 26 guests