George and all who have one or both of these blades:
It seems that the blades that Gord and I have are the Cub-54 Leveling and Grader Blade 1949 to 1952 version.
I have the complete blade except for the one rod which I can fabricate quite easily if I can get the measurements. The part that I need is the Front Lifting Rod - part # 650 136 R2, and the Rear Lifting Rod - part # 650 135 R1. I need the overall length, and the length of the bent portions. They appear to be straight 90 degree bends, so if someone would be good enough to mark up the part illustrated on Page 13 of the McCormick Deering Leveling and Grader Blade and send it to me, I would be very very grateful! I am assuming that these parts are identical to the 1949 to 1952 version, I hope
Also, in my desire to get what I wanted, I had the lifting arm assembly for the Cub-54 Leveling and Grader Blade 1953 and since version fabricated, as well as the spacer blocks etc.
Obviously, I still have a few parts to make if I want to convert it entirely to the later model. However, I have a feeling that with the parts I have already had fabricated, including the substitute draw bar, that I might be able to get the best of both worlds so to speak.
Question 1 is: Can I use the lifting bar pictured below (angle iron with another piece of angle iron welded to it that is hooked to the front lifting rod, then to the tool bar rod and then to the front lifting bars) along with the lifting arm assemble from the 1953 and since version
Question 2 is. What are the major differences between the pre 53 and the post 53? Is the performance similar? I do understand that the lifting arm assembly has been beefed up a lot, and I am hoping to use this.
If I cannot use the parts I have, then I will need to have a few extra parts made (hope not). I want to be able to have both these blades up and operational ASAP as the snow is due pretty soon!
Thanks guys
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Cub 54 Blades - model vs model?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Cub 54 Blades - model vs model?
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
BLADE PARTS
IF I WAS YOU I WOULD JUST GIVE TOM AT TM TRACTOR A CALL AND HE CAN SELL YOU ANY PART YOU NEED FOR YOUR BLADE. I HAVE DEALT WITH HIM AND HE IS VERY HELPFUL, BESIDES THAT HIS PARTS BOLT RIGHT ON AND THEY ARE NOT EXPENSIVE FOR WHAT YOU GET.
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Bill:
Yup, I know that. Deal with Tom as much as I can. However, by the time I get the part here I may as well buy another Cub WITH A BLADE! That is why I have to make a lot of what I need. Shipping, Customs, taxes and border fees usually are many times the value of the part purchased
Yup, I know that. Deal with Tom as much as I can. However, by the time I get the part here I may as well buy another Cub WITH A BLADE! That is why I have to make a lot of what I need. Shipping, Customs, taxes and border fees usually are many times the value of the part purchased
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
Who is online
Users browsing this forum: No registered users and 38 guests