Hi all,
I put on a Cub54 Grader blade on my 1949 Cub recently (front mount) and also put on some new skid shoes for it. I'm sure it will plow or push snow alright but the problem is, raised all the way up, the blade is only 2 or 3 inches off the ground. The blade drags the ground going into the garage and is kind if limiting my non-snow "tractorin"
Do any of you other folks see about the same thing?
Any ideas about how to raise it higher?
My setup is exactly the same as this one from over at TM parts.
http://www.tm-tractor.com/gim/blade54_001.htm
I appreciate the help. Its good to know we have a place to ask other like minded folks to share their experience.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Cub 54 Grader Blade Doesn't Raise Much
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- Dave.49.cub
- 10+ Years
- Posts: 66
- Joined: Fri Apr 16, 2004 10:43 am
- Zip Code: 45066
- Tractors Owned: 1949 Farmall Cub - Working Tractor -Mowing, log skidding, snow plowing.
1947 Farmall Cub - My Dad's - Location: OH, Springboro
Cub 54 Grader Blade Doesn't Raise Much
Dave.49.cub
- John *.?-!.* cub owner
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
- Dave.49.cub
- 10+ Years
- Posts: 66
- Joined: Fri Apr 16, 2004 10:43 am
- Zip Code: 45066
- Tractors Owned: 1949 Farmall Cub - Working Tractor -Mowing, log skidding, snow plowing.
1947 Farmall Cub - My Dad's - Location: OH, Springboro
The touch control hasn't leaked any and seems to easily raide my Woods mower way up and set it right down and also will hold mower up indefinitely. The flat piece your referred to is just like the one I have, the long cylindrical pin with the 2 90 degree angles that dows the lifting looks like mine too. Looks like if it was about 4 inches longer it would do much better!
Dave.49.cub
- Dave.49.cub
- 10+ Years
- Posts: 66
- Joined: Fri Apr 16, 2004 10:43 am
- Zip Code: 45066
- Tractors Owned: 1949 Farmall Cub - Working Tractor -Mowing, log skidding, snow plowing.
1947 Farmall Cub - My Dad's - Location: OH, Springboro
If you look on this page:http://www.tm-tractor.com/gb/gb_001.htm the first to pics of bellcrank assemblies.
I have the standard and not the boomerang type.
I have the standard and not the boomerang type.
Dave.49.cub
-
- 10+ Years
- Posts: 37
- Joined: Thu Jan 29, 2004 6:10 pm
- Location: waterford michigan
blade won't lift much
Dave I'm in the process of putting a cub-54 grader blade on. Tomorrow "Tuesday" I will check out how high it lifts, and let you know. Looks like I have the same set-up as you do. Last year I used this blade, but used the boomerang type adaptor this year I have the standard set -up. I have one more wheel weight to install tomorrow and will start her up. Mike
- ChickenWing
- 10+ Years
- Posts: 108
- Joined: Sat May 22, 2004 1:46 am
- Location: MI, Temperance
I had the same problem a couple of weeks ago. I posted a thread, but there didn't seem to be anyone who knew what the problem was. So I went out and got me a piece of 6"x12" - 1/4" steel plate, and made a bracket up to extend the lift.
I drilled holes to bolt the plate onto the rockshaft. Then I set the lift handle to the all the way down position (mine is manual, not TC). Then I hooked the bellcrank extention to the top pin of the rockshaft while the blade was sitting flat on the ground. Then I marked where the second bellcrank hole lined up on the steel plate, and drilled a hole there. I bolted it up, and then I got full movement of the blade along the movement of the lift lever. Now it goes probably 7 inches up, or so. I still cant figure out why it doesn't lift up otherwise? Mine would only go up about 1 inch before. It seems most of my movement would be downward, helpful for deep grading, but not for snowplowing.
I drilled holes to bolt the plate onto the rockshaft. Then I set the lift handle to the all the way down position (mine is manual, not TC). Then I hooked the bellcrank extention to the top pin of the rockshaft while the blade was sitting flat on the ground. Then I marked where the second bellcrank hole lined up on the steel plate, and drilled a hole there. I bolted it up, and then I got full movement of the blade along the movement of the lift lever. Now it goes probably 7 inches up, or so. I still cant figure out why it doesn't lift up otherwise? Mine would only go up about 1 inch before. It seems most of my movement would be downward, helpful for deep grading, but not for snowplowing.
- cjpenny89
- 10+ Years
- Posts: 1080
- Joined: Mon Feb 03, 2003 1:15 pm
- Location: St. Charles, MI 48655
First of all check all your pivot points on the blade and make sure they are not loose. Mine were wobbled out so I took a drill and went to the next size pin and drilled them out. I also took the front mount with the spring and drilled a hole lower so it could pick it up a few more inches.
I then did not like the 5/8 threaded rod that the blade pivoted on so I replaced it with and yes had to drill out the pivot blocks but I used a 3/4" TG&P shafting I had from work and I use split lock collars to lock it down.
My blade raises about 10"-12" now and it really made a difference.
Just check all your joints if each one wiggles a little it will add up to a lot in the end.
Chad Penny
I then did not like the 5/8 threaded rod that the blade pivoted on so I replaced it with and yes had to drill out the pivot blocks but I used a 3/4" TG&P shafting I had from work and I use split lock collars to lock it down.
My blade raises about 10"-12" now and it really made a difference.
Just check all your joints if each one wiggles a little it will add up to a lot in the end.
Chad Penny
-
- 10+ Years
- Posts: 37
- Joined: Thu Jan 29, 2004 6:10 pm
- Location: waterford michigan
blade lift
Dave
I completed installing the blade on the cub today, The blade lifts 10". I have the same set-up as shown on th TM tractor web site. If possible checkout how far the touch control arms move from one stop to another.
Mike
I completed installing the blade on the cub today, The blade lifts 10". I have the same set-up as shown on th TM tractor web site. If possible checkout how far the touch control arms move from one stop to another.
Mike
- Dave.49.cub
- 10+ Years
- Posts: 66
- Joined: Fri Apr 16, 2004 10:43 am
- Zip Code: 45066
- Tractors Owned: 1949 Farmall Cub - Working Tractor -Mowing, log skidding, snow plowing.
1947 Farmall Cub - My Dad's - Location: OH, Springboro
- ChickenWing
- 10+ Years
- Posts: 108
- Joined: Sat May 22, 2004 1:46 am
- Location: MI, Temperance
I had a request for photos of the bracket I made, so I thought I'd post them here. They are kinda big.
You can see I had to cut a square about 3"x3" out to mount if flat. I also need to cut the corner off nearest the clutch pedal, as I am not able to push the clutch when the blade is mid range. It works fine when completely lowered, or raised. It is quick job, just haven't gotten to it yet. That is the only modification that needs to be done right now. Other wise it works well, and extends the lift upward.
You can see I had to cut a square about 3"x3" out to mount if flat. I also need to cut the corner off nearest the clutch pedal, as I am not able to push the clutch when the blade is mid range. It works fine when completely lowered, or raised. It is quick job, just haven't gotten to it yet. That is the only modification that needs to be done right now. Other wise it works well, and extends the lift upward.
Who is online
Users browsing this forum: Bb Bob and 51 guests