Been working on a cub that belongs to the local Lions Cub as I get time and feel like it. Yesterday I decided to sand blast the hood Cubguy47 had provide to replace theirs which was in pretty bad shape. I have one of the cheap Harbor Freight pressurized sand blasters, which works good but uses a lot of air. I have a stationary air compressor the delivers 10.7cfm at 90psi, and a portable that delivers 5.5 at 90 psi, and have my airlines set up so I can run both of them when I am sandblasting. Even with that, they do not quite keep up with the blaster, but do come close. I got out all my rigging, the blaster, a poncho, respirator, hood, gloves, etc. and fired up. After about 20seconds my air pressure was too low to blast, so I stopped and checked the gauge on blaster and on both compressor tanks. All checked ok, so I started again, and got the same results. When I looked at all the gauges all was ok, so I concluded that for some reason I had a restriction in an airline, and the blaster which is a pressurized tank type would fill with air, but would was not receiving air fast enough to maintain pressure. I use a 25 foot hose to feed a 50 foot reel mounted on one wall. It was close enough that I could bypass it with a single 25 foot hose, so I got out the extra hose to run it out to the blaster. When I started to connect the hose I realized I had not opened the valve to feed air from the big compressor into the line. Opened the valve and all was well.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Sandblasting the hood
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Sandblasting the hood
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- Cub Pro
- Posts: 5238
- Joined: Sat Sep 08, 2007 3:49 pm
- Zip Code: 25271
- eBay ID: yogiefisher
- Tractors Owned: 37 John Deere A
63 Farmall Cub
53 Farmall Cub
56 Farmall Cub
IH 140
Massey 165 & 250 - Circle of Safety: Y
- Location: WV. Ripley
Re: Sandblasting the hood
Looks great John, now will you paint it with a sandable primer to help fill the rough texture after blasting ?
I did a little over half of a 54 blade and a couple front rims tonight after work, that yellow paint on the blade seems to be about 1/16" thick.
A little paint stripper helped the job go easier.
I did a little over half of a 54 blade and a couple front rims tonight after work, that yellow paint on the blade seems to be about 1/16" thick.
A little paint stripper helped the job go easier.
Democracy is two wolves and a lamb voting on what to have for lunch. Liberty is a well-armed lamb contesting the vote.
Ben Franklin
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: Sandblasting the hood
This is a working tractor, not a show rig, and it will probably get a coat of Vansickle primer followed by IH 2150 after it dries. The hood needs a little minor repair before it is primed though.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 908
- Joined: Sat Feb 15, 2003 7:20 am
- Zip Code: 00000
Re: Sandblasting the hood
John,
Where are you getting your sand at?
Where are you getting your sand at?
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: Sandblasting the hood
Local lumber yard. I use the fine silica (white) sand,since it does not clump if it gets damp, etc. Using silica sand you definitely need a good cartridge type respirator not just one of the little dust masks, silica dust is a carcinogen.JackF wrote:John,
Where are you getting your sand at?
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- Similar Topics
- Replies
- Views
- Last post
-
- 6
- 263
-
by ricky racer
Sun Mar 24, 2024 6:14 pm
-
- 3
- 680
-
by Glen
Thu Jan 04, 2024 2:15 am
-
- 1
- 144
-
by Dale Finch
Tue Oct 25, 2022 4:03 pm
-
- 6
- 519
-
by Pap
Fri Apr 29, 2022 7:59 am
-
- 5
- 331
-
by Ky Cub
Sun Nov 12, 2023 3:07 pm
Who is online
Users browsing this forum: Inspectorjoe, Majestic-12 [Bot] and 4 guests