This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
weak loader- cycling hydraulic pump?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 130
- Joined: Fri Apr 27, 2007 3:02 pm
- Location: Ansonia, CT
weak loader- cycling hydraulic pump?
I have a henderson loader which has cylinders which were recently rebuilt by a hydraulic shop. It has its' own hydraulic pump seperate from the standard cub touch control hydraulics. I don't think I ever cycled the system properly as it has been pretty weak since I reinstalled the cylinders. It would hesitate before lifting and even once lifting it was not able to lift much of a load. I thought the fluid level was low so I added more; I think I must have over filled it because when I downward pressure with the bucket, fluid would pour out of the vent cap. I am guessing the weak lift is due to air in the line, but I don't have much experience with hydraulics. I could use tips on how to cycle the pump to get the air out and any other advice.
-
- 10+ Years
- Posts: 2680
- Joined: Mon Oct 24, 2005 11:35 am
- Zip Code: 14072
- eBay ID: toysforjake
- Tractors Owned: Lots of Cub Cadets!
1951 Farmall Cub
1977 IH Cub
1966 IH Cub
1965 IH Lo Boy
1964 IH Lo Boy
1949 Farmall Cub
Several IH 154 Lo Boys
1979 IH 184 Lo Boy
Simplicity 4416 Sovereign
Simplicity Conquest
Simplicity Legacy 4x4 Diesel
Mitsubishi MT180D 4x4 Diesel - Circle of Safety: Y
- Location: Grand Island, NY
Re: weak loader- cycling hydraulic pump?
Typically, hydraulic systems like front end loaders, need to be cycled fully up, fully down, many times in a row, just to bleed out air. It does sound like you have over filled it, but that will typically not hurt anything since the extra just pukes out the vent. On most loaders, the reservoir is just a little bigger than what is needed for the cylinders to be fully extended.
If the pump is driven from the PTO (as I'm guessing) your engine speed will also effect the pump speed, therefore, it is probably designed to operate correctly with the engine running at wide open throttle, or at least 2/3 throttle. The henderson loaders are not very fast to begin with, but it should be able to lift several hundred pounds pretty easily.
If the pump is driven from the PTO (as I'm guessing) your engine speed will also effect the pump speed, therefore, it is probably designed to operate correctly with the engine running at wide open throttle, or at least 2/3 throttle. The henderson loaders are not very fast to begin with, but it should be able to lift several hundred pounds pretty easily.
Cub Cadets 682, 1811, 1864, Simplicity Legacy XL 4x4 Diesel with FEL, 60" mower, 50" Tiller
-
- 10+ Years
- Posts: 4949
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: weak loader- cycling hydraulic pump?
When dealing with a loader that uses one-way cylinders (power up, gravity down) ALWAYS fill the reservoir with the loader completely lowered to the ground. Otherwise you will get overflow, as you found out.
Any pump powered by the tractor engine will vary in speed and strength based on how fast the engine is running. If you can't lift anything with the tractor running wide open, then the pump is probably shot.
Take Bill's advice above, run the loader all the way up and down several times to work out the air. If the loader stops before it goes all the way up, you've run out of oil. Drop it back down and top off the reservoir.
Any pump powered by the tractor engine will vary in speed and strength based on how fast the engine is running. If you can't lift anything with the tractor running wide open, then the pump is probably shot.
Take Bill's advice above, run the loader all the way up and down several times to work out the air. If the loader stops before it goes all the way up, you've run out of oil. Drop it back down and top off the reservoir.
-
- 10+ Years
- Posts: 130
- Joined: Fri Apr 27, 2007 3:02 pm
- Location: Ansonia, CT
Re: weak loader- cycling hydraulic pump?
The pump is attached by belt to the engine. Even at full throttle in neutral, it is very weak. Probably the pump. Not sure what to do about that... pump is visible in this thread viewtopic.php?f=1&t=62306&p=514913#p514913
Any thoughts on converting it to run off of the touch control?
Any thoughts on converting it to run off of the touch control?
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: weak loader- cycling hydraulic pump?
My Henderson doesn't have an outboard hydraulic pump. It gets plumbed to the Touch Control. So you should be able to plumb yours through the Touch Control as well. Remember that you will need to make sure that the reservoir is filled. Pay attention to what Matt mentioned... I think that would be important. I would probably plumb it similar to the way I plumbed the splitter project.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: weak loader- cycling hydraulic pump?
The control lever assembly has a safety valve in it that may be set too low, or the spring may be weak broken.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 130
- Joined: Fri Apr 27, 2007 3:02 pm
- Location: Ansonia, CT
Re: weak loader- cycling hydraulic pump?
Thanks to all. Plenty of things to check into.
-
- Team Cub Mentor
- Posts: 20378
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: weak loader- cycling hydraulic pump?
Conduct a pressure test on pump. Guessing, you will need 1200 psi or hopefully much more out of the pump.ozimmerman wrote:The pump is attached by belt to the engine. Even at full throttle in neutral, it is very weak. Probably the pump. Not sure what to do about that.
See if there is some sort of identification on the pump or system. If there is, perhaps you can determine it's capabilities.
I have an excuse. CRS.
-
- 10+ Years
- Posts: 130
- Joined: Fri Apr 27, 2007 3:02 pm
- Location: Ansonia, CT
Re: weak loader- cycling hydraulic pump?
Well, it was a simple fix. The belt was too loose. It was tight enough for the tractor to run, but as soon as the loader had any weight on it, the belt would slip at the hydraulic pulley. Adjusted the pump to tighten the belt and it works fine. Still might look into plumbing it to the touch control, but it isn't critical at this point.
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: weak loader- cycling hydraulic pump?
Glad you got it fixed and that it really was only a minor issue. Thanks to for reporting back on what the problem was Enjoy playing with your loader
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 4949
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: weak loader- cycling hydraulic pump?
Ah, the Achilles heel of belt-driven hydraulic systems.
Yes, you can power your loader off the touch control. It requires a bypass block, some plumbing, and an external reservoir connected to the fill pipe of the TC unit. Lots of info on this modification on this forum.
Yes, you can power your loader off the touch control. It requires a bypass block, some plumbing, and an external reservoir connected to the fill pipe of the TC unit. Lots of info on this modification on this forum.
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Hydraulic help - pump cavitation with loader Attachment(s)
by cobra2411 » Sun Jan 09, 2022 9:41 pm » in Farmall Cub - 35
- 1016
-
by ricky racer
Thu Feb 03, 2022 11:09 am
-
-
- 2
- 174
-
by Glen
Sun Sep 04, 2022 5:18 pm
-
-
Key stuck in hydraulic pump Attachment(s)
by Workinprogress » Tue Jun 14, 2022 5:09 pm » in Farmall Cub - 18
- 409
-
by Dale Finch
Thu Jun 16, 2022 7:30 am
-
-
- 6
- 273
-
by coppersmythe
Sat May 07, 2022 9:20 pm
-
- 24
- 644
-
by Glen
Wed Apr 12, 2023 8:40 pm
Who is online
Users browsing this forum: Majestic-12 [Bot] and 10 guests