Page 1 of 2

Hydraulics modification

Posted: Thu Nov 29, 2012 11:19 pm
by Bob Perry
(This question is for the inventors, not the purists.) :P :P :P

I'm curious if anyone has modified or seen pictures of modifications, to run a 2nd hydraulic pump off the front of a Cub engine. I have one idea in mind, but before I start making it, I'd be curious if anyone has pictures of such an invention.

This of course is not a Cub engine but an example of what I mean:

Image

Re: Hydraulics modification

Posted: Thu Nov 29, 2012 11:42 pm
by lazyuniondriver
I saw a modification very similar to the picture you posted except it was a York AC compressor on the right side of the engine to keep the farmer cool on his stool in his cab. I believe it was an IHC as well.

The only thing which struck me as odd was there was no provision for belt adjustment. The belt length required was measured then bumped on or railed with a screwdriver or something.

The fab guy claimed building an adjustable platform was way too complicated so when it starts slipping 3 bucks tightens it. (70's or 80's prices)

The cab air did work well. I had occasion to borrow it for a few days in trade for charging the system.

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 12:12 am
by Bob Perry
Sounds cool !

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 12:20 am
by lazyuniondriver
Bob Perry wrote:Sounds cool !

It was... Even cooler when R-12 was around a buck a pound.

Keep in mind the AC was on a Diesel and it did drop the RPM a little when it cycled on. Since the cub is a little low on the HP scale, factor in the work you intend to do with the pump.

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 4:19 am
by Eugene
Years ago, Farmall A (?) had a power steering pump mounted on right front of engine. Hydraulics for raising and lowering mower deck. Was church owned. Power steering pump had a pretty good sized reservoir, probably off a larger truck.

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 7:18 am
by ScottyD'sdad
Bod a double sheve crankshaft pulley would be a great drive point. (found on some combine power units). Ed

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 7:29 am
by Gary Dotson
Space constraints make it very difficult to mount a belt driven pump (or anything else) to the C-60. The generator location is about the only location that the belt would have a clear run to. I used a BMW power pump to power the hyd. system on Cubota but it's Kubota engine is an entirely different deal.

Years ago, my brother installed a Ford power steering on his Farmall B, as a lift pump for his cultivators, to replace the exhaust lift. When he restored the tractor, a few years ago, he removed it. Now, he's considering putting it back on.

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 8:12 am
by gpcub
I used a Prince pump on the PTO of my "H" years ago to run my log splitter. Might be easier then a pump of the engine.

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 9:51 am
by Bob Perry
ScottyD'sdad wrote:Bod a double sheve crankshaft pulley would be a great drive point. (found on some combine power units). Ed

You have one for me?
Gary Dotson wrote:Space constraints make it very difficult to mount a belt driven pump (or anything else) to the C-60.

I'm thinking of taking the alternator down, outside of hood, essentially the alt. and pump would both be outside hood.

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 9:51 am
by Bob Perry
gpcub wrote:I used a Prince pump on the PTO of my "H" years ago to run my log splitter. Might be easier then a pump of the engine.

gotta be live for my application

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 10:03 am
by Matt Kirsch
Have you considered mounting it to the front bolster and driving it through the crank hole, directly off the crankshaft?

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 10:25 am
by Eugene
Electric powered hydraulic pump. I have grain truck hoist powered by 12 volts directly connected to battery. Controls are a hand held push button. The hydraulic pump, electric motor, and reservoir, are approximately 14 to 18 inches long and about 12 inches tall. This system is single action - up. Haven't researched the topic. Probably double action systems available.

Edit: E-bay has some 12 volt powered hydraulic pumps listed. Worth considering, might be the least expensive way to go.

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 10:30 am
by CapeCodCubs
You need to stop by Lonnie's across the street from me. If you want to build something he knows how to. Great guy...awesome shop....fabrication skills beyond believe. All the local pullers are having him build their tractors.

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 10:54 am
by Rudi
Bob:

Check this out:

Image

1941 Farmall A with 1000 Loader!

This should solve some of the questions about an outboard pump on a Cub. Although the Cub has a smaller engine - it should work. I have heard of others using fan hub powered pumps on Cubs before and it kinda makes sense in a way. However, the only way to know for sure is to well, try it.

and this thread might be useful as well

Image

That pump was used on the Cub PTO but should fit up front.

farmall cub fever in Maine

Re: Hydraulics modification

Posted: Fri Nov 30, 2012 11:49 am
by Eugene
Industrial Fluid Power, Womack Educational Publications. Appendix C, "Drive Horsepower for Hydraulic Pump".

1500 psi at 85% pump efficiency. 3 gallon per minute pump takes 3.09 HP. 5 gallon per minute pump takes 5.15 HP. 7.5 gallon per minute pump takes 7.72 HP.

1250 psi pump at 85% efficiency. 3 gallons per minute takes 2.57 HP. You can use the previous figures to approximate the HP required to power what ever pump you obtain.

Simply idling the pump at zero psi takes approximately 5 percent of the pumps maximum rated horsepower.

Depending on intended application and proposed usage, the Cub engine may or may not be up to it.