Farmall Cub Forum -- Questions and answers to all of your Cub related issues.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds
or one of our site sponsors for your tractor and parts needs.
Mon Dec 10, 2012 9:57 am
Some advice sought about how to best repair a Cub radiator finned-tube leak. The leak is located on the lower right portion of the radiator tube bank...where a tube passes through the lower copper sheet metal head/panel. Fluid slowly seeping and pooling on the top of the axle casting...and is only noticeable after parking. I tried to solder the leak with the radiator mounted to the tractor but leaking persists. I believe my soldering process was wrong or, with the radiator on the tractor, I could not get sufficient heat on the parts. I am prepared to dismount the radiator this time...could someone share the correct soldering process with me (type of solder, amount of heat, flux, etc)?
Mon Dec 10, 2012 10:06 am
Boss Hog recommend a radiator sealer a while back. If Boss say's it is good, you can bet I will use it on my next leak.
I will see if I can find the thread.
Mon Dec 10, 2012 10:20 am
Spotlessly clean repair site and plenty of flux. Mapp gas instead of propane if you don't have an oxy/acetylene torch and the tube completely drained so heat from the torch isn't carried away. If all of the above conditions are met, you should have no problem sealing a puncture wound. Cancer may be harder seal, sometimes the whole tube must be removed and the remaining stubs sealed top and bottom.
Mon Dec 10, 2012 10:46 am
On a "last leg's" radiator my Farmer Fix goes like this. Be gentle as you can, but get it done.
Needle nose pliers-Remove all fins 1.5" to 2" above and below the leak. A gentle back and forth twist will break the fin, next to the tube.
Set of dyke's or shop scissors- cut out a 1/2" to 1" piece of the leaking tube.
Flat Screwdriver- spread the tubes open where cut. (top and bottom)
Permatex (your favorite color(I like the red))- [Complete one before beginning the other] Squeeze as mush permatex as you can, deep into the tube. Now take the needle nose and pinch the tube shut (1/2"). Then, fold the tube using the pliers width as a guide. Pinch tight, then repeat.(2 folds)
Do the other end and it will not leak
Mon Dec 10, 2012 11:05 am
Dale Shaw wrote:Squeeze as much permatex as you can, deep into the tube.
That would create a plug like you have to remove from the end of an opened tube. Never thought about that approach but on a no or low pressure system... Good idea. A lot easier than soldering.
Mon Dec 10, 2012 11:19 am
Above topic lists the product and method I used to seal up a very leaky radiator on a 154 Cub low-boy.
Mon Dec 10, 2012 11:39 pm
Many moons ago a neighbor rammed the rear of my 1936 chevrolet with a a1938 buick. We plugged his radiator leak with juicy fruit chewing gum. He just hoped to get home that way. Bob ran the car another 3 or 4 years that way. Had to be early 50's.
I had success sealing bad tubes on a neighbors C. I cleaned the bad tubes with a 22 cal brass wire bush and then with muriatic acid i had put a piece of zinc in. Then I used regular copper tubing flux and soldered using 50/50. It held for a number of years till George died and his kids sold the tractor. Got the zinc from an old dry cell battery. I have been trying to remember why i did it that way and come up with a blank. Only guess is because one of my grand fathers taught me that way.
Powered by phpBB © phpBB Group.
phpBB Mobile / SEO by Artodia.