TC pump removal help

[Jdbfish]

How do you remove the bottom bolt next to the block to remove the touch control pump? It is so close to the pump body, I can't get anything on it to turn it. Please help!!!!!

[Dale Finch]

Only two of the four bolts hold the pump onto the tractor...the other two hold the two pump halves together. Can't swear which ones are which (they are diagonally across from each other) but I KNOW someone with more knowledge will chime in! I believe you will need to use an open end wrench on the lower one.

If I remember right, try removing the outer (left) upper one, and if it is long enough to screw into the block and loosens the pump, then it should be the lower inner bolt to complete the removal.

[Don McCombs]

Maybe this photo from TM Tractor Parts will help.

[Dale Finch]

In that photo the pump is on its side, so I do believe it is the upper left and lower right bolts to remove the pump. And now that I think about it, I think you use a box wrench on that lower one...

Anyway, good luck!

[Jdbfish]

Using the pic above,, it is the bottom left bolt I can't remove. There isn't enough clearance between the bolt head and pump body to get a wrench on. I've tried open end, box end, and sockets in both six and eleven point but no luck with either.

[cubguy47]

Try a 3/8" drive socket with a short extension, it has thinner side walls, I use one all of the time and it works well. Good luck.

[cubguy47]

Or even a 1/4" drive socket too would work, not sure what tools you have on hand.

[lazyuniondriver]

Pictured is what I prefer to use in cramped spaces such as you describe. I think a standard short socket and a separate U joint would also work, both on a short 3/8" drive extension bar.

Attachments

1355287202-picsay.jpg (38.36 KiB) Viewed 428 times

1355287293-picsay.jpg (52.87 KiB) Viewed 428 times

[tst]

The bolts are 1/2" not 7/16"
Tim

[Jdbfish]

I have tried all the 3/8 drive sockets i have but will try1/4 drive and the. 6 point swivel socket. Hopefully something will work

[lazyuniondriver]

The bolts are 1/2" not 7/16"
Tim

Looking at the picture, it is evident the pump has been off before, difficult access perhaps the very reason for substituting 1/2" head cap screws with the pictured 7/16" heads. The line block's fasteners retain the original 1/2" heads.

[Boss Hog]

Dang , lazyuniondriver, Have you ever even taken a hydraulic pump off a cub before?
The bolts are 5/16 with a 1/2 inch head.
Jdbfish, take a 3/8 drive socket and grind it down on the outside until it is a smaller diameter if you dont have a 1/4 inch drive that has a thin enough wall. use a 6 point and an extension. Also make sure that it is clean around the head of the bolt. Sometimes you will need to drive the socket on if you can not get it clean around the head of the bolt.
Boss

[lazyuniondriver]

Dang , lazyuniondriver, Have you ever even taken a hydraulic pump off a cub before?

Yes.

[Scrivet]

The bolts are 1/2" not 7/16"
Tim

Looking at the picture, it is evident the pump has been off before, difficult access perhaps the very reason for substituting 1/2" head cap screws with the pictured 7/16" heads. The line block's fasteners retain the original 1/2" heads.

I see your pictures and I see one borrowed from TM to illustrate which bolt positions hold the pump together and which ones hold the pump to the block.
I don't see the one you are referring to from Jdbfish who is the one with the question and problem.

[lazyuniondriver]

The bolts are 5/16 with a 1/2 inch head.

No, the bolts in the illustration are 5/16" with 7/16" heads. 5/16" capscrews come with multiple sized heads.