Built 3 of these this weekend
Moderator: Team Cub
5 posts
• Page 1 of 1
Built 3 of these this weekend
by Clint Carter » Sun Jan 13, 2013 2:49 pm
Had a cole planter setting around and thought i would make it more useful to the fleet and built me a one point hitch for it. Have one I was thinking of parting with, (not sure yet) so though i would make one for it to. Well I might run across one down the road so i will make one to have on hand, I guess i will stop there. Sometimes it is just as easy to make more then one when you have all the tools out and going, and when my brain gets going, witch is rare it is hard to stop. Thanks to Boss for the measurements and some of the steel
- Attachments
-
Have A Nice Day!
-
Clint Carter - Cub Star!!
- Posts: 464
- Joined: Thu Jan 06, 2011 5:46 pm
- Location: NC
- Zip Code: 27265
- Tractors Owned: Ford 2000
78 Cub Fast Hitch Red
78 Cub Red
76 Cub Red
75 Cub (Not Long Stripe) Yellow
70 Cub Yellow Fast Hitch
53 Cub 151 Disk Plow
69 Cub 
- Circle of Safety: Y
Re: Built 3 of these this weekend
by Winfield Dave » Sun Jan 13, 2013 3:17 pm
Dave
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill
-
Winfield Dave - 501 Club
- Posts: 2412
- Joined: Thu Apr 22, 2010 2:31 pm
- Location: PA, Middleport (Schuylkill County)
- Zip Code: 17953
- Tractors Owned: ......Almost enough
- Circle of Safety: Y
Re: Built 3 of these this weekend
by danovercash » Sun Jan 13, 2013 5:32 pm
Clint, if you didn't taper the bottom of the point, I would do that. Don't ask how I know! Also some shims on the sides like the original Cole planter to lessen "slop". Looks like a very good job and should work well.
"It is impossible for a man to learn what he thinks he already knows." -Epictetus
252646 & 221525. 195897 (Gone but not forgotten!)
http://groups.yahoo.com/group/dansfarmallcub/
252646 & 221525. 195897 (Gone but not forgotten!)
http://groups.yahoo.com/group/dansfarmallcub/
- danovercash
- 501 Club
- Posts: 2403
- Joined: Mon Feb 17, 2003 8:48 pm
- Location: NC, Kannapolis
- Zip Code: 28081
- Circle of Safety: Y
Re: Built 3 of these this weekend
by Clint Carter » Sun Jan 13, 2013 6:59 pm
what do you mean taper the bottom of the point? How will that help? Thank you.
Have A Nice Day!
-
Clint Carter - Cub Star!!
- Posts: 464
- Joined: Thu Jan 06, 2011 5:46 pm
- Location: NC
- Zip Code: 27265
- Tractors Owned: Ford 2000
78 Cub Fast Hitch Red
78 Cub Red
76 Cub Red
75 Cub (Not Long Stripe) Yellow
70 Cub Yellow Fast Hitch
53 Cub 151 Disk Plow
69 Cub - Circle of Safety: Y
Re: Built 3 of these this weekend
by danovercash » Sun Jan 13, 2013 8:05 pm
Start at the bottom front of the and remove 1/8" to3/32" over about 4
" . The drawbar has several bends in it. Check a factory point, they are not flat on the bottom either.
" . The drawbar has several bends in it. Check a factory point, they are not flat on the bottom either.
"It is impossible for a man to learn what he thinks he already knows." -Epictetus
252646 & 221525. 195897 (Gone but not forgotten!)
http://groups.yahoo.com/group/dansfarmallcub/
252646 & 221525. 195897 (Gone but not forgotten!)
http://groups.yahoo.com/group/dansfarmallcub/
- danovercash
- 501 Club
- Posts: 2403
- Joined: Mon Feb 17, 2003 8:48 pm
- Location: NC, Kannapolis
- Zip Code: 28081
- Circle of Safety: Y
5 posts
• Page 1 of 1
Who is online
Users browsing this forum: Trackwelder and 7 guests
|
|