Clutch Throw-Out BearingModerator: Team Cub
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
8 posts
• Page 1 of 1
Clutch Throw-Out Bearing
Hi all - We're well into a complete restoration of our 1948 Farmall Cug - Serial Number 21005.
I'm sure someone here knows how to tell if the clutch throw-out bearing is worn out. It is smooth but not flat as I would expect. I tried taking a photo of it but it does show the depression that's all the way around as you'd would expect   PleaseBest regards, Ken
Re: Clutch Throw-Out Bearing
A depression is normal on a used bearing. Does it have pieces broken out/ how much graphite is showing past the housing? Here is a new one form Tm Tractors website for comparison.
 "The Constitution is not an instrument for the government
to restrain the people, it is an instrument for the people to restrain the government lest it come to dominate our lives and interests." Patrick Henry
Re: Clutch Throw-Out Bearing
Thanks for the prompt reply with photos. The graphite portion is slightly thinner than what's shown in your photograph, but not by much. I think we're good to go as is - or as we're doing with so much of this tractor - Hey we've got it apart why not change it so it's new? I wonder?
Thanks again, Ken
Re: Clutch Throw-Out Bearing
Ken:
G'day to you and congrats on being the proud keeper of a '48 Cub. Ellie my '48 is my go to Cub ,,, and they can get addictive. Clutch TOB wearing ... advanced search of the forum archives = worn clutch tob Suggest you take a bit of time and become familiar with the [urlhttp://www.cleancomputes.com/Cub/Cub%20Owner's%20Manuals/index.html]Owner's Manual[/url] and the Service Manuals. The GSS-1411 Service Manual for Cubs and Lo-boy Tractors Revision 1 Section 5 - Engine Clutch should be of help.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
Re: Clutch Throw-Out Bearing
Ken, There are aftermarket TO bearings that tend to quickly fail. They also need to be filled with a low temp grease so the grease can permeate the graphite and lube the face. A lot of guys soak them in oil before insertion. While you are in there, check and make sure the adjustment on the 3 fingers is correct and all the same. Welcome to the Forum.
Bob "We don't need to think more,
we need to think differently." -Albert Einstein
Re: Clutch Throw-Out Bearing
If the current TOB is showing nearly as much graphite as the one in the picture, I would leave it and use the money for some other portion of the restore.
I had the same feeling, but at $65 a pop, I decided that based on the amount of wear (a bit more than you describe) it was good for at least another 10 years. Michael Cummings
Eddie - a 1959 International Lo-Boy named after my father in law, who who bought her new.
Re: Clutch Throw-Out Bearing
Michael, based on what we've found as we've gotten more of it disassembled - the TOB will remain as is. It's nicely and evenly worn.
Best regards and thanks so much for posting to my question.
Re: Clutch Throw-Out Bearing
You are most welcome, pvf. Just remember to grease the TOB. This is one instance where you want to use the cheapest grease. The graphite wicks the oil out of the grease, and the cheaper greases seem to work better.
Michael Cummings
Eddie - a 1959 International Lo-Boy named after my father in law, who who bought her new.
8 posts
• Page 1 of 1
Who is onlineUsers browsing this forum: Arthur Dent, baldwindiesel, ericofmaine, RonT, waterboychuck and 7 guests |
|
to Farmallcub.com 
Forum Family. And you have come to the right place for all things Cub related. If you click on the 
the 
