Page 1 of 1
What the heck are these????
Posted: Sun Apr 07, 2013 7:23 pm
by vwfish
Hi All,
New cub owner here again.
So it's almost spring-like around here and it's time to remove the plow and attach the mower.
First question:
How does that belt go on?!
Question 2:
What are the attached, what do they do and how do I use them?
Thanks!
Re: What the heck are these????
Posted: Sun Apr 07, 2013 7:26 pm
by Rudi
#1 is the Touch Control Front Rockshaft - looks like the Boomerang is attached.
#2 is the TC Rockshaft Rod - connects from the Touch Control front rockshaft to the rear rockshaft
#3 is the mounting brackets for the IH Danco C-2 Mower I think
#4 .. not sure
Re: What the heck are these????
Posted: Sun Apr 07, 2013 7:37 pm
by tst
#1 hand lift front rockshaft
#2 rear rockshaft lift rod
#3 are cub loboy C2 & C3 mounting brackets
#4 do not think its for a cub
tim
Re: What the heck are these????
Posted: Sun Apr 07, 2013 7:59 pm
by Boss Hog
I agree with Tim
Re: What the heck are these????
Posted: Sun Apr 07, 2013 8:04 pm
by Barnyard
And the boomerang on that rockshaft will not work on a TC rockshaft if I'm not mistaken.
Re: What the heck are these????
Posted: Sun Apr 07, 2013 8:16 pm
by Rudi
Yup.. #1 is the Hand Lift Rockshaft. Keep forgetting that one even though I have two on the shelf
Re: What the heck are these????
Posted: Mon Apr 08, 2013 5:33 am
by Bill E Bob
I noticed in the illustration, the use of a straight rockshaft rod, yet the drawing shows a long ear dash.
Is the requirement for an off set rod unnecessary when using a manual lift?
Re: What the heck are these????
Posted: Mon Apr 08, 2013 8:15 am
by jim turner
Barney, I use the boomarang on my hand lift for the grader blade is this not correct?
Re: What the heck are these????
Posted: Mon Apr 08, 2013 8:20 am
by Barnyard
jim turner wrote:Barney, I use the boomarang on my hand lift for the grader blade is this not correct?
Jim, You would still use a boomerang regardless of which rockshaft you have, but it is my understanding the boomerang on a manual lift rockshaft will not fit a TC rockshaft.
Re: What the heck are these????
Posted: Mon Apr 08, 2013 8:57 am
by John *.?-!.* cub owner
Barnyard wrote:jim turner wrote:Barney, I use the boomarang on my hand lift for the grader blade is this not correct?
Jim, You would still use a boomerang regardless of which rockshaft you have, but it is my understanding the boomerang on a manual lift rockshaft will not fit a TC rockshaft.
It will bolt on, but the hole where the lift rod attaches does not line up with the one in the rockshat.
Bill E Bob wrote:I noticed in the illustration, the use of a straight rockshaft rod, yet the drawing shows a long ear dash.
Is the requirement for an off set rod unnecessary when using a manual lift?
I have never tried the straight rod with a handlift, but sighting along the mounts it appears that it would rub sometimes, especially if the hole is in the top hole of the hand lift.
Re: What the heck are these????
Posted: Mon Apr 08, 2013 10:00 am
by Denny Clayton
tst wrote:#1 hand lift front rockshaft
#2 rear rockshaft lift rod
#3 are cub loboy C2 & C3 mounting brackets
#4 do not think its for a cub
tim
Yup, Lo-Boy
only.