Wed Jun 05, 2013 8:17 am
Spindles need to turn such that they run onto the blade bolts/nuts. Blade needs to be sharp on the leading side. Hope this is not confusing. Works this way on every mower I have had experience with (RM600,59).
Wed Jun 05, 2013 8:28 am
vwfish wrote:Well funny thing is both sides of the deck are open, so I guess it could be either side discharge at this point.
Now I know the blades are spinning clockwise as you look down and the bolts tighten the same way.
Do I need different blades and route the belt the opposite way so the blades spin the other direction?
Yes. My deck spins clockwise also and my bolts tighten counter clockwise with right hand threaded bolts. And they get tighter with use! Are your blades upside down by any chance? And the belt on without the 3/4 twist? The blades are bent down from the center about 1/2" below the center bolt level. Are yours? And the sharp edge on the blade is to the bottom of the blade surface so the cut grass gets forced up in the cutting action.
Wed Jun 05, 2013 8:50 am
This is a confusing thread. A right hand thread tightens in the clockwise direction. If your threads are good then the only way I can think of to keep bolts from loosening is to change direction of rotation. Doesn't matter if the blade is upside down as far as the bolt is concerned.
Wed Jun 05, 2013 10:16 am
OK - currently your blades spin clockwise as looking from above. It still sounds to me like you have LH threads on your spindle. So - I believe your deck is set up as a LH discharge deck as are your blades. All you need to do is reverse the belt drive to accommodate your deck. Is that even possible? Where and how would you cross the belt to reverse the rotation, between the deck and the mule drive? I can visualize it but I'm not sure the belt wouldn't rub against itself.
Wed Jun 05, 2013 10:25 am
No, he's going to need different blades too...
If he reverses the direction of rotation, the current blades will be spinning in the wrong direction. They won't spin the bolts out but they also won't cut anything either... UNLESS they are installed upside-down now.
Wed Jun 05, 2013 10:30 am
I have a woods (I think) mower and the darn blades keep unscrewing and falling off....
I think some pictures of your mower deck might be helpful. A couple from each side of the mower deck above showing the belt lay out and discharge, and one from the bottom showing the blade setup would help. If you do not have a way to post them on line you can send them to me email@example.com
and I will post them for you. This link will take you to manuals for the woods mowers used on cubs. One note, if your mower uses 3 belts rather than one it is probably a C3 (Ih or Danco) not a Woods. http://www.farmallcub.com/[ Sorry, direct links to manual section is not allowed. ]/index.p ... rs&order=0
Wed Jun 05, 2013 10:38 am
ricky racer wrote:Remember, the Cub PTO turns backwards compared to the rest of the world.
Boy, this is turning into the misinformation thread. The Cub PTO spins correctly, it's just the rest of the world that spins backwards.
My wife is left handed and thinks the rest of the world is screwed up!!
Wed Jun 05, 2013 10:43 am
Matt Kirsch wrote:If he reverses the direction of rotation, the current blades will be spinning in the wrong direction
I think he has left hand blades.
John *.?-!.* cub owner wrote:I think some pictures of your mower deck might be helpful
You're right John - a picture or two is worth a thousand words or two!
Wed Jun 05, 2013 12:57 pm
It sounds like you have a left hand deck, left handed bolts, and a right handed belt and blades. You need to switch to all left or all right. You may be able to cross the belt to spin to the left and get left handed blades. I had a similar problem so I just drilled and helicoiled the spindles to right hand.
Tue Jun 18, 2013 7:47 pm
I will post pictures when I get a chance.
However I rattled the bolts tight with a pneumatic wrench and then haven't fallen off again......yet.
Wed Jun 19, 2013 3:14 pm
In your original post you describe a left handed thread but called it a right handed thread.... I don't know if there-in lies your problem or it was a freudian slip... But it sure is weird that your blades keep falling off....But first I would figure out what threads you have....And then the direction of the blades and see if they coincide....Dave
Wed Jun 19, 2013 3:19 pm
Ricky your wife is right or I should say correct....I too am left handed which puts me in my right mind ?????? along with all other lefties...But I still have my ear anyhow...
Thu Jun 20, 2013 7:27 am
My identical twin is a southpaw... course he is also an Airhead (read RCAF) .. I am right handed and a squid - aka Navy. Nuf said...
Thu Jun 20, 2013 10:42 am
Well Rudi, I was an Army Infantryman in Nam....2/35th, 25th Inf Div....Then Special Forces 1/11th....But if you want to believe the Navy rules, thats ok with me......Maybe....
Dave.....Back to the mower what cha ma jig....I don't know which model woods is involved but EX 12a on the ih c2 mower manual shows the belt crossing between pulleys...Maybe whichever model woods you have does the same....Dave
Powered by phpBB © phpBB Group.
phpBB Mobile / SEO by Artodia.