Sat Jun 15, 2013 9:16 pm
I was looking at the manual trying to figure out how the 101A attaches when you have a fasthitch. It says to use a headless bolt. Is this just as it says headless bolt or is it something special bolt?
Thanks in advance for your help !!
Sat Jun 15, 2013 9:43 pm
the main difference is the chain tightener and bracket, the rest is the same I think
Sat Jun 15, 2013 10:03 pm
Do you have any pics ?
Mon Jun 17, 2013 5:23 pm
Maybe I should clarify some. I was talking about where the brace attaches to the final housing when you have fast hitch and the depth adjusting lever . Does anyone have the 101A installed with the brace mounting to the fast hitch bracket? pic of the headless bolt or it dimensions?
Mon Jun 17, 2013 9:45 pm
i have one on mine , but no headless bolt
Tue Jun 18, 2013 9:10 am
I think a headless bolt may be one with the "head" in the middle, and threads sticking out both ends. This way you can tighten it down on the depth control, and leave it there. Then you can install the side dresser any time you feel like it. Or, it's just a stud.
All you should need is a bolt approximately 1/2" longer than the one that's in there. Just bolt through both the brace and the depth lever.
Fri Jun 21, 2013 9:07 pm
Ok Thanks guys
Sat Jun 22, 2013 9:44 am
Does anyone have the measurement for the brace, chain tighter bracket for the fast hitch ? The brace looks to be aflat piece of steel but the tighter bracket looks to be in a different location than what's on the non fast hitch type.
Sat Jun 22, 2013 5:18 pm
If you get by here you can see one up close and personal
or I can get the measurements
Sat Jun 22, 2013 8:34 pm
you are looking for a slotted head set screw fl-pt 5/8-11unc x 1" it should have come with the countershaft brace when new sigma fastners has a picture hope this helps this has to be used if you have the lever type fast hitch it screws into the top hole on the final drive
Last edited by t jackson on Sun Jun 23, 2013 10:26 pm, edited 1 time in total.
Sat Jun 22, 2013 9:08 pm
I am not sure I follow all that is being discussed here, but when I saw the mention of a headless bolt it got my attention. Last year at my "mini fest" some helpful guys managed to remove a headless bolt in the top front implement hole in my '55 cub's right final. When I get home tomorrow I will post a photo and if it is what you are looking for, you may have it.
Sun Jun 23, 2013 3:29 am
I would like to see a photo of the headless bolt. I do have the lever type fast hitch. Old iron, Wade, started this post and I just had some more questions so if he has the screw thype fast hitch and doesn't need this type bolt I would like to have it. When I get down the boss I guess I'll be able to see what it looks like close up. Thanks for the replies.
Sun Jun 23, 2013 8:28 pm
that would be great !!! thank you !!!
Mon Jun 24, 2013 12:08 am
This was the post I made a while back trying to determine what the bolt/screw was for. http://www.farmallcub.com/phpBB2/viewtopic.php?f=1&t=75157
Is this what you are talking about?
Mon Jun 24, 2013 4:53 pm
Here is the link to the manual where it talks about the "headless bolt"
Thanks Wadehttp://www.cleancomputes.com/Cub/Cub%20 ... age-03.jpg
Powered by phpBB © phpBB Group.
phpBB Mobile / SEO by Artodia.