Farmall Cub Forum -- Questions and answers to all of your Cub related issues.
Moderator: Team Cub
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
12 posts • Page 1 of 1
my cub just started throwing belts, I had no problems last year. I have a c3 rotary mower, using b112 belts. This year I cannot keep a belt on for more than 5 minutes. Looking a the rear idler pulleys, they don't even line up straight with the center pulley on the mower. Idlers are fixed (can go up and down) but they really need to angle left or right. As I watch the belt when the PTO is engaged, it looks like the left idler rolls the belt and the center pulley throws it off. Any suggestions to fix this, last year no problems, this year-frustrated..
G'day to you. Sorry to hear you have problems keeping the belts on your C-3. Here is the manual for it - C-3 Rotary Mower 12-20-63
Will this help?
We have a lot of resources for our members and I would suggest that you might want to spend a little time following the links below.
Welcome to the forum from Arkansas. Use my C-2 very little, but I know it has to have the right belt and a good quality belt and be adjust right. There are some folks on here that know them inside out, but welcome.
Guiena, 1951 Farmall Cub; Jumping Willy, 1949 Farmall Cub.
Once the belt breaks the cord on the inside they will not stay on.
1975 cub (LouAnn) serial # 245946, 1941 John Deere Model H
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
Have you tried a new belt?
Did you remove the mower for the winter, then reinstall it? Perhaps you reinstalled something incorrectly?
Does this look familiar?
Thanks for the quick replies. New belt being used, B112
haven't taken the mower off.
The rear end has the pto, and two idler pulleys below , fixed, can go up and down, but off set at an angle.
I haven't had any problems changing a belt before and this us now my third belt
Are the pulleys rusty or scored? What brand belt? Same as last year or different?
Okay, if you have a new belt you should have had to move the pulleys to install it. More than likely, you just have an alignment problem. Take a piece of string or a straight edge long enough to reach the idler from the drive pulley. Pull it flat down the face or side of the drive pulley and it should fall into the sheave of the idler. If the pulleys are not aligned all the new belts in the county won't stay on.
If you're gonna dream or steal, do it BIG
The best things in life aren't things.
lots more junk
Thanks for the replies. I put on an older belt and have the best luck so far. Today it finally is done. None of the new B112 belts stay on. I only had to move the idler pulley up to get the belt off. Attached photo on the back/pto. The idler pulley go down the left of the tractor but the mower pulley is in the middle. Last year, no issues with belts staying on, this year can't mow. Any help appreciated. Thanks.
Check a few alignments. From drive pulley on PTO to idler pulleys, belt should be perfectly vertical. If not, adjust drive pulley on PTO shaft to make it vertical. From idler pulleys on mule drive to canter pulley on deck, belts should be as close to horizontal as possible, and as close to in one plane (together) as possible. Don't let one pulley run much lower than the other. If alignment is correct, then be sure all pulleys turn free with no wobble. Also be sure none of the pulley lips (sheaves) are broken or worn. After that, the only problem remaining is the belt.
'52 Cub ("Great Personality") 148xxx
'48 Cub with FH ("Gunny Cub") 38xxx
'57 Lambretta (a slow work in progress)
'74 Triumph TR6 (Mama's toy)
Had the same problem awhile back.....The PO had a notched belt as a main belt and when it broke I replaced it with a b112....Off they came ( I tried several)....Then I looked at the manual and noticed the main belt went to the top notch on the pulley on the mower(at least in the manual , I looked at) and not the center notch as the PO had put it on....Put a Kelvar b112 and ran it to the top notch and ....problem solved....Been a year now with no problems.....That just my experience...Worked for me....Dave
In Memory of 58,286
What condition are the bearings and hubs on the deck, particularly the center one? Not that it matters but is that an A you're working on? The draw bar set up looks different than a Cub.
Attachments - 193 plow - 144 cultivator - 22 mower - 28A disc harrow - 54 leveling blade - Woods 59C2 - drag harrows - Mott D9 flail
12 posts • Page 1 of 1
Who is online
Users browsing this forum: smars4444 and 3 guests