These were advertised for a Cub LOBOY. Will these also fit a standard Cub?
What (if any) are the risks of using these spacers to widen the space between rear wheels?
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Rear wheel spacers?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 10
- Joined: Wed Jan 22, 2014 10:34 pm
- Zip Code: 53517
-
- Team Cub
- Posts: 11859
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: Rear wheel spacers?
Yes, They will fit (you could verify that with the seller if you have any concerns). No risks that I am aware of as long as you make sure you keep the bolts tight. What are you going to do on the front end if you go to 58"?
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 10+ Years
- Posts: 1573
- Joined: Sun Feb 02, 2003 11:01 pm
- Zip Code: 36310
- Tractors Owned: 1975 IH cub,1948 farmall cub,1979 international 3200 skid steer and a 1974 John deere 350B dozer.
- Location: Abbeville Alabama
Re: Rear wheel spacers?
those are for a numbered series lo boy that use the wide turf tires. Yes they will work on a std cub but for what reason I dont know.
Collector of Farmall cubs and cub cadets.Injoy helping people keep their cubs running. Years of experipnce.
- Barnyard
- Team Cub
- Posts: 24271
- Joined: Tue Aug 07, 2007 3:39 pm
- Zip Code: 45030
- Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100 - Circle of Safety: Y
- Location: OH, New Haven (Hamilton County)
- Contact:
Re: Rear wheel spacers?
I'm not sure how well your axle tube will hold up with the stress from being so much wider.
There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.
-
- 10+ Years
- Posts: 2791
- Joined: Tue Jul 22, 2008 12:44 pm
- Zip Code: 48370
- Tractors Owned: 184
- Location: Oxford, MI
Re: Rear wheel spacers?
I had a set of aluminum spacers for my numbered series.
While they performed the task of moving the wheels out (for chains), they did wear out.
The holes where the bolts fit were not tapered to match the bolts. They eventually wore slack and then allowed the bolts to waller (not a northerner term) out the mounting holes. Had to remove the tires and tighten them up twice a year.
Eventually, one failed while on a slope and caused an usafe removal of the rear tire breaking off all but one lug bolts.
I believe the failure was caused by using a tapered shoulder lug bolt rather than a flat-shouldered bolt. If using these, spend the money on the proper bolts, steel flat washers, and lock washers.
I have purchased the steel version of spacers that has an IH part number. No issues since. Don't need to retighten.
http://www.tugedge.com/p/Services#%2fCub_Cadet%2fCub_185_Lo-Boy_Tractor%2fRear_Wheel_Spacer_(Floatation_Tires)%2f011840-A%2f0118400071
Note: The picture you have shown looks like the bolts go through the rim & wheel spacer. This would be easier to retighten. The set I had was different. 5 bolts mounted the spacer to the axle, and had 5 studs that protruded through the rim and fastened the rim with nuts.
While they performed the task of moving the wheels out (for chains), they did wear out.
The holes where the bolts fit were not tapered to match the bolts. They eventually wore slack and then allowed the bolts to waller (not a northerner term) out the mounting holes. Had to remove the tires and tighten them up twice a year.
Eventually, one failed while on a slope and caused an usafe removal of the rear tire breaking off all but one lug bolts.
I believe the failure was caused by using a tapered shoulder lug bolt rather than a flat-shouldered bolt. If using these, spend the money on the proper bolts, steel flat washers, and lock washers.
I have purchased the steel version of spacers that has an IH part number. No issues since. Don't need to retighten.
http://www.tugedge.com/p/Services#%2fCub_Cadet%2fCub_185_Lo-Boy_Tractor%2fRear_Wheel_Spacer_(Floatation_Tires)%2f011840-A%2f0118400071
Note: The picture you have shown looks like the bolts go through the rim & wheel spacer. This would be easier to retighten. The set I had was different. 5 bolts mounted the spacer to the axle, and had 5 studs that protruded through the rim and fastened the rim with nuts.
184 w/ Creeper & 3-Point
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
- SONNY
- 10+ Years
- Posts: 4113
- Joined: Thu Nov 09, 2006 11:26 pm
- Zip Code: 61722
Re: Rear wheel spacers?
Any excess width is going to cause damage to the tractor on down the road. ---I know how to widen the front axle,-- BUT there again would NOT be good on a cub! thanks; sonny
Who is online
Users browsing this forum: No registered users and 56 guests