How to remove and install new valve guides

Farmall Cub Forum -- Questions and answers to all of your Cub related issues.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.

How to remove and install new valve guides

Postby Virginia Joe » Mon May 05, 2014 8:21 pm

Below is how I replaced valve guides in a Farmall Cub. Special thanks goes to Tom (Tractorboy3) for his advice that made it possible.
You will need one 3” long x 5/16 grade 8 and nut and bolt, a small spacer and a piece of flat iron with a hole drilled in it.
Image

After removing the valves, place the flat stock on top of the block and inset the bolt through the old valve guides.
Image

Now place the nut on the bottom of the bolt.
Image

Then turn the nut with a ratchet and open end wrench until the nut almost bottoms out on the block. At this point, unloosen the nut, install the spacer and nut, and continue to tighten until the guide is free.
Image

Tom said it perfectly;
I pulled my guides out from the top, without removing cam shaft. Used a bolt, and assorted washers...they came right out...then I put the new guides in the freezer overnight, warmed the block...and the new ones went in easily...
Yes that will work. If I remember correctly, once the nut on the bottom reaches the block, you will need to remove the nut and add some spacers that are smaller in diameter than the guide to finish pulling it all the way out...Warming the block and putting the new guides in the freezer overnight worked like a charm when re-installing. Take them out of the freezer one at a time when installing...I used an old guide and bolt as an alignment tool to gently drive them back in...They should go in real easy to the depth you measured on the originally installed guides....Tom


Installing the guides:
I put the new valve guides in the freezer overnight. To install them, I grabbed the same bolt used in the removal process and placed on it an old valve guide (turned it upside down) and slid it onto the bolt.
Image

Then heat the block with a torch directly around the valve space you are installing.
Image

Get the new valve from the freezer and slip it onto the bolt and valve shown below.
Image

Now drive the valve into position using a hammer to hit the top of the bolt until you have it to the correct depth.

Best of luck,
Joe Letteri
Virginia Joe
Cub Star
Cub Star
 
Posts: 177
Joined: Mon Oct 12, 2009 7:00 pm
Zip Code: 23005

Re: How to remove and install new valve guides

Postby Barnyard » Wed May 07, 2014 3:16 pm

Thanks for the info Joe. I will copy this into the "How To" forum also.
It is common sense to take a method and try it. If it fails, admit it frankly and try another. But above all, try something.
- Franklin D. Roosevelt -

Barnyard Bash CubFest May 30th - May 31st, 2014
Click here for info http://www.barnyardbash.com
http://www.Savethecub.com
User avatar
Barnyard
Team Cub
Team Cub
 
Posts: 17862
Joined: Tue Aug 07, 2007 3:39 pm
Location: OH, New Haven (Hamilton County)
Zip Code: 45030
Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100
Circle of Safety Award
Circle of Safety: Y

Re: How to remove and install new valve guides

Postby Tractorboy3 » Thu May 08, 2014 10:23 am

Nice job...Glad it worked out for you as I described...Thanks for the quote.... :D
'50 H, '52 Super C, '54 Cub, '57 Cub, '58 Cub, '95 Cub Cadet 1440
User avatar
Tractorboy3
5+ Years
5+ Years
 
Posts: 151
Joined: Thu Jan 29, 2009 9:54 pm
Location: Laurel, Md
Zip Code: 20707
Tractors Owned: ........
1950 H
1952 Super C
1954 Cub
1957 Cub
1958 Cub
1995 Cub Cadet 1440


Return to Farmall Cub

Who is online

Users browsing this forum: ad356, Dale Finch, Glen, RUSSALL, sford, Spuds Buddy and 6 guests