Hi All
Received the hydraulic by-pass block in today’s mail. I need to remove my exhaust pipe and muffler so I can install the by-pass block however I also need to bend the exhaust pipe before I reinstall it. I am thinking of just replacing it with a new one and bend it before I install it.
Ok here is the question where can I buy a new exhaust pipe
1958 cub under slung exhaust
http://i19.photobucket.com/albums/b152/ ... ader20.jpg
Thanks
Rick
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Still working on the LOADER INSTALL
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- Ricaroo
- 10+ Years
- Posts: 179
- Joined: Sat Jun 19, 2004 5:37 pm
- Location: New Hampshire
- beaconlight
- 10+ Years
- Posts: 7703
- Joined: Thu Aug 19, 2004 2:31 pm
- Zip Code: 10314
- Location: NY Staten Island & Franklin
Rick I can't help you with the exhaust but I see that you have a bolt and flat washer holding up the cycle bar mower. To the best of my knowledge that should be a taper headed bolt. They cut out wiggle and wear.
They are the ones similar to front wheel bolts on a cub or thse on a car.
Bill
They are the ones similar to front wheel bolts on a cub or thse on a car.
Bill
Bill
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
- Scott
- 10+ Years
- Posts: 1194
- Joined: Sun Dec 26, 2004 7:09 pm
- Zip Code: 02769
- eBay ID: scottdarowski
- Tractors Owned: 48 Cub
55 Cub
62 CCO
63 CCO
70 JD 112 - Location: MA, Rehoboth
- Contact:
- allenlook
- Cub Pro
- Posts: 1795
- Joined: Sat Jul 31, 2004 10:37 pm
- Zip Code: 12020
- Location: NY, Saratoga Springs
- Contact:
Underslung exhaust
Got one from TM a while back - just put it on today.
I know what you mean about the bypass block, my muffler runs just past the hydraulic plate, in fact I think it's touching slightly, so with the block you're sure to have some interference...
I know what you mean about the bypass block, my muffler runs just past the hydraulic plate, in fact I think it's touching slightly, so with the block you're sure to have some interference...
Searchable Cub Parts Database and Manual Galleries at www.farmallcub.info - Computerized Carving at www.bitcarving.com
- Dan Robertson
- 10+ Years
- Posts: 311
- Joined: Thu Feb 06, 2003 4:08 pm
- Zip Code: 47421
- eBay ID: gotowin
- Tractors Owned: 55 cub,
74 cub,
Cub Cadet 1515,
Case 580B TLB,
53 Ford Jubilee,
MF 271XE,
JD 3130,
JD gater - Location: Bedford, IN
Who is online
Users browsing this forum: No registered users and 45 guests