Hi, from NE Florida

[wbran001]

Hello, Joined not long ago and you all have already helped me. I have inherited a 1955 Cub from my Dad. Looking forward to getting it running. I'm in Green Cove Springs, Fl. Thanks.

[Tezell]

Welcome to the forum.

[T-Mo]

Welcome to the forum.

[Mike in Louisiana]

Welcome to the forum.

[Steve Butram]

Welcome to the forum

[Glen]

Hi,
The Cub operator's manual can help you learn about maintenance that the Cub needs.

Below is the 1955 Cub operator's manual. The experts on here recommend people read it. It has lots of info about operation, maintenance, and lubrication. There is a table of contents on page 1, and the index begins on page 70.
It shows how Cubs originally looked in it. The lube section begins on page 14.

http://farmallcub.com/rudi_cub/www.clea ... index.html

It shows the electrical system that a 1955 Cub originally had.
Cubs made before mid 1964 originally had 6 volt, positive ground electrical systems.
They have said on here that IH didn't make a new manual every year.

The Touch Control fluid mentioned in the manual for the Touch Control, was changed later to Case IH Hy-Tran fluid. It is sold at Case IH dealers.
There are other brands, be sure it works with IH hydraulic systems before buying one.

I would check or change all the oils before using the Cub. Using it with low oil in a gear housing can damage the parts in the housing.
There are 3 separate gear housings, with 3 separate oil levels to check, in the rear area of a Cub, the transmission, and 2 final drives.

The transmissions in Cubs commonly get water in them, from rain, or condensation inside the housing over time.

The air cleaner is an oil bath air cleaner. Dirt that is sucked in settles to the bottom of the oil cup. It should have clean, light motor oil in the oil cup to work right.

There are 2 pages gone in the lube section, pages 19 and 20.
Below are pages from the manual made after this one with the missing info.

http://farmallcub.com/rudi_cub/www.clea ... e%2026.jpg

http://farmallcub.com/rudi_cub/www.clea ... e%2027.jpg

http://farmallcub.com/rudi_cub/www.clea ... e%2029.jpg

Good luck with the Cub.

[Stanton]

Welcome to the Forum! Nice to hear you inherited your family Cub.

Take some time and read through a few threads to acquaint yourself with the Forum:

• Welcome Wagon
• How to Upload Pictures to a Post
• Forum Picture Posting And Other Interesting Things You Can Do
• Using the Forum

Don't know if you have any of the manuals to your Cub, but after your 2nd post on the Forum, you'll have access to the all the PDF Manuals on this site. There’s a few ways to do that:

• From a desktop or laptop, go to "Quick Links" in the upper left corner of your screen. Hit that and a pull-down appears where you'll find "PDF Manuals".
• You can also go to “Cub Info” in the upper toolbar, then hit “Rudi’s Manuals”. From there, you can access a variety of information.
• If you're using a phone, go to the "Links Directory" (second category down the main page). Once in "Links Directory" , scroll down to the second section "Tractor Parts & Manuals" and you'll find them there.

You'll be able to download an Owner's Manual (very strongly recommended) and any service manuals that interest you. Implement Manuals are also available.

We’d encourage you to take the Safety Test located in the Safety Forum: http://farmallcub.com/phpBB2/viewtopic.php?f=33&t=68084

Might also enjoy reading through this thread (even though it’s for a Cub, much can be applied to any tractor just brought home): What to do with a Cub you just brought home

There are a lot of good threads dealing with Cub repair and maintenance in the How To Forum. Located here: http://farmallcub.com/phpBB2/viewforum.php?f=11

Take some pictures of your tractor and post them, we’d like to see it.

Remember:
• When you have a specific question, start a new thread in the appropriate sub-forum.
• Before posting, use the Preview button before hitting Submit--it'll show you exactly what your post will look like, including pictures.
• When adding your comments to a thread, be sure to look at the date of the last poster. If it’s more than a 6 months old, the posters are probably not going to see it. Consider starting a new thread.

Glad you joined us.