This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
hello from middle tn
-
- 5+ Years
- Posts: 3
- Joined: Tue May 06, 2014 4:32 pm
- Zip Code: 37096
hello from middle tn
Just wanted to say hello and yall sure have a ton of info to take in.
-
- 5+ Years
- Posts: 3
- Joined: Tue May 06, 2014 4:32 pm
- Zip Code: 37096
Re: hello from middle tn
I've had my cub about a week. Its supposed to be a 49 model but the serial number tag is gone. Love it so far but I gonna have to get a plow and cultivators. I've mowed the grass noticed a little extra movement in the mower shaft. I took the mower off and yep it gonna need bearings. I dont know what type of mower it is no tags, but on the bottom of it it says Danuse mach tulsa ok. I put it back on greased it and mowed some more and I must have put the belt on wrong be cause its almost toast. I assume the v goes down into the two pulleys on the tractor and the mower as well. Well guys looks like I need parts. Hope I haven't rambled for to long.
- randallc
- Cub Pro
- Posts: 1906
- Joined: Tue Jan 18, 2011 9:16 am
- Zip Code: 72940
- Tractors Owned: 1951 Farmall Cub, 152 disk plow, 2 gang disk, belly mower, sickle mower
1949 Farmall Cub, cultivator, moldboard plow, disk,front blade. Cub Cadet, LTX1045 Mower. Cub Cadet's 109, 125, 1000, and 1250
1961 cub c2 belly mower and full blade. 48 cub manual lift with cultivators.
1947 Cub - Circle of Safety: Y
- Location: Huntington, AR
Re: hello from middle tn
Welcome to the forum from Arkansas. Yes, the guys have put a lot of work into this site. Valuable! Should be able to find some information on the cast numbers on each part that will help identify your cub. Post a picture of your mower and someone should be able to identify what you have.
- Mike in Louisiana
- 10+ Years
- Posts: 7825
- Joined: Tue Feb 15, 2005 10:10 am
- Zip Code: 71023
- Circle of Safety: Y
- Location: LA, Doyline
Re: hello from middle tn
Welcome to the forum. Look around and you will find the answer to most questions.
1975 cub (LouAnn) serial # 245946, 1941 John Deere Model H
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
-
- 10+ Years
- Posts: 3369
- Joined: Mon Feb 17, 2003 8:48 pm
- Zip Code: 28081
- Circle of Safety: Y
- Location: NC, Kannapolis
Re: hello from middle tn
Check for engine serial# just above and to the right of the carb. Would be slightly higher than tractor SN. Also look for casting codes on large cast pieces. Two numbers and a letter ( example 5•7•A). This will help date the tractor.
"I'd rather be a mechanic in the shop"- Henry Ford
252646 & 221525. 195897 (Gone, but not forgotten)
252646 & 221525. 195897 (Gone, but not forgotten)
- BIGHOSS
- Cub Pro
- Posts: 1741
- Joined: Tue Jul 18, 2006 9:55 pm
- Zip Code: 37087
- Tractors Owned: 1947 Cub S/N 9216
w/ C-22 Mower
1974 Cub S/N 244814
w/59 Woods Mower
Ford 3000 Gas S/N C375091 w/Bushhog QT2345 Loader & 6' Squealer Bushhog
and a Palomino Mare named GIGI - Circle of Safety: Y
- Location: TN, Lebanon
Re: hello from middle tn
Welcome from another Middle TN resident. I am in the Lebanon area.
"Courage is being scared to death-but saddling up anyway".......John Wayne
- LeeC
- 10+ Years
- Posts: 343
- Joined: Fri Oct 31, 2008 2:07 pm
- Zip Code: 22150
- Tractors Owned: 2 1962 LoBoys
1 1964 LoBoy
1 1965 LoBoy
1 1966 LoBoy - Circle of Safety: Y
- Location: Springfield, VA
Re: hello from middle tn
Welcome to the forum.
Danuser Machine Works = Danco
If it only has one pulley on top of the deck, it is a Danco C2 mower. Parts are still sold through CaseIH.
Here is a link to the operator's manual on Rudi's manual server http://www.cleancomputes.com/Cub/Cub%20Implement%20Manuals/C-2%20Rotary%20Mower/index.html There is a link to Rudi's Manuals at the top of this webpage. It is an invaluable resource. --Lee
pcviking wrote:I dont know what type of mower it is no tags, but on the bottom of it it says Danuse mach tulsa ok.
Danuser Machine Works = Danco
If it only has one pulley on top of the deck, it is a Danco C2 mower. Parts are still sold through CaseIH.
Here is a link to the operator's manual on Rudi's manual server http://www.cleancomputes.com/Cub/Cub%20Implement%20Manuals/C-2%20Rotary%20Mower/index.html There is a link to Rudi's Manuals at the top of this webpage. It is an invaluable resource. --Lee
-
- 5+ Years
- Posts: 3
- Joined: Tue May 06, 2014 4:32 pm
- Zip Code: 37096
Re: hello from middle tn
Thanks for mower info! I'm sure the info was already on here and I've been looking but I get to reading this thread and then that one and I get sidetracked.
Return to “Introduce Yourself”
Who is online
Users browsing this forum: No registered users and 13 guests