I have just bought a IH Model A cub
Don't know if it is super or non super but want to get a manual
The date stamp is 7-24-c Which is 1957 I believe
The manuals I find online are for Prior to 1957
Will this be of any value to me?
If anyone can direct me to a link for a manual
I could sure use it.
Thanks
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Question
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
Re: Question
LT - the date code is a 57 date code but Super A's were no longer in production at that time. I don't know which casting you took the date code from but it is possible something has been replaced. The serial number for the tractor should be located at the right hand seat rail. It also would be either an A or Super A and not an A cub. Cubs were a whole different model. See if you can locate your serial number and then you should be able to identify what you have. Manuals are available either through a Case IH dealer or from Binder Books at www.binderbooks.com
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
- Team Cub Mentor
- Posts: 20377
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Question
An IH A and a Cub are two different tractors.
Depending on you mechanical ability I would suggest the I&T manuals for your tractor. The I&T IH-8 covers both the Cub and A series tractors. But the I&T manuals are for a more experienced mechanic.
Once the tractor is identified, obtain the operators. service manual and parts manual.
Depending on you mechanical ability I would suggest the I&T manuals for your tractor. The I&T IH-8 covers both the Cub and A series tractors. But the I&T manuals are for a more experienced mechanic.
Once the tractor is identified, obtain the operators. service manual and parts manual.
-
- 10+ Years
- Posts: 6
- Joined: Mon May 24, 2010 4:17 pm
- Zip Code: 72031
Re: Question
Thanks for the replys
The 7-24-c is on the right side of the engine
Below the seat it shows Model A FAA Serial # 212090
I am not and experienced mechanic
But belive there will be plenty work to do on this old tractor
Thanks again
The 7-24-c is on the right side of the engine
Below the seat it shows Model A FAA Serial # 212090
I am not and experienced mechanic
But belive there will be plenty work to do on this old tractor
Thanks again
-
- Team Cub
- Posts: 17278
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: Question
That serial is a 1947 Farmall A. Could the code on the block be 7-24-Q? If it is a C code, the block has been replaced or the tractor is some sort of mix-n-match.
-
- 10+ Years
- Posts: 6
- Joined: Mon May 24, 2010 4:17 pm
- Zip Code: 72031
Re: Question
Jim
It just may be a Q the little tail isn't much now and it's so close to the screw that it's hard to tell.
on the side of the transmission there is a 6-28-7 if that helps.
Sure want the right manual.
Thanks
Louis
It just may be a Q the little tail isn't much now and it's so close to the screw that it's hard to tell.
on the side of the transmission there is a 6-28-7 if that helps.
Sure want the right manual.
Thanks
Louis
-
- Team Cub
- Posts: 17278
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: Question
OHV engine? 4-speed transmission? no hydraulics? It is an A.
-
- 10+ Years
- Posts: 6
- Joined: Mon May 24, 2010 4:17 pm
- Zip Code: 72031
Re: Question
Thanks Jim
Now I know which manual to get.
Now I know which manual to get.
Return to “Farmall A, Super A, AV, 100, 130 & 140”
Who is online
Users browsing this forum: No registered users and 5 guests