This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Fuel starvation?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- havoc1482
- 10+ Years
- Posts: 987
- Joined: Fri Sep 20, 2013 11:17 am
- Zip Code: 01085
- eBay ID: havoc1482
- Tractors Owned: _______ 1948 Farmall Super A
- Circle of Safety: Y
- Twitter ID: @havoc1482
- Location: Westfield, MA
- Contact:
Fuel starvation?
Okay, so I put my Super A back together. When I go to start it, it stays running for a maximum of like 3 seconds then just stops. Then It won't start up again for a few minutes. If I spray starting fluid into the intake it will do the same thing. I also noticed at the carb there is a fuel leak where the rubber hose meets the carb. I cleaned the carb before I installed it so there shouldn't be anything in there. Although I have a feeling there is a blockage somewhere and its not letting enough fuel through to keep it running. I assume its running until it eats up the starting fluid/whatever fuel is in the carb.
Other than that the tractor sounded amazing in the few seconds it was running. Have a new head with new valves cold gapped at .016 (I haven't been able to hot gap it yet). New plugs (Champion D21s) and this time SAE-20 instead of -30 oil because 30 is just too damn thick in this cold.
Also, on another note, I had a brain fart and mixed my coolant as 1/3 water and 2/3 coolant. Is that bad and should I drain it then remix it 50/50 or can I leave it? At least I won't have to worry about it freezing
Other than that the tractor sounded amazing in the few seconds it was running. Have a new head with new valves cold gapped at .016 (I haven't been able to hot gap it yet). New plugs (Champion D21s) and this time SAE-20 instead of -30 oil because 30 is just too damn thick in this cold.
Also, on another note, I had a brain fart and mixed my coolant as 1/3 water and 2/3 coolant. Is that bad and should I drain it then remix it 50/50 or can I leave it? At least I won't have to worry about it freezing
Mike
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
-
- Team Cub Mentor
- Posts: 20369
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Fuel starvation?
Anti freeze tester, test and check the results to see if anti freeze reading is below the lowest expected temperature for your area. I would flush the cooling system next summer then install a 50/50 mix.
Fuel starvation. Start checking for fuel flow at the carburetor, then work back to the fuel tank.
Normally if the problem is low fuel flow, tractor engine off for a while, the tractor will run for a minute or two before the starvation issue begins.
Had a similar problem with an H. The rubber fuel line was the problem. Great fuel flow when disconnected from carb. Reconnect, tractor would run great for a minute, then die.
Fuel starvation. Start checking for fuel flow at the carburetor, then work back to the fuel tank.
Normally if the problem is low fuel flow, tractor engine off for a while, the tractor will run for a minute or two before the starvation issue begins.
Had a similar problem with an H. The rubber fuel line was the problem. Great fuel flow when disconnected from carb. Reconnect, tractor would run great for a minute, then die.
I have an excuse. CRS.
- havoc1482
- 10+ Years
- Posts: 987
- Joined: Fri Sep 20, 2013 11:17 am
- Zip Code: 01085
- eBay ID: havoc1482
- Tractors Owned: _______ 1948 Farmall Super A
- Circle of Safety: Y
- Twitter ID: @havoc1482
- Location: Westfield, MA
- Contact:
Re: Fuel starvation?
Will test the fuel line issue today. Last night I n ever let it sit for more than 1-2 minutes before trying to start it. Possibly today with the time it sat enough fuel worked its way into the carb, it might run for more than 3 seconds.
And according to the chart on the back of the coolant bottle (Traveller) I will be protected up to -62*F with a 2/3 mix haha
And according to the chart on the back of the coolant bottle (Traveller) I will be protected up to -62*F with a 2/3 mix haha
Mike
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
- havoc1482
- 10+ Years
- Posts: 987
- Joined: Fri Sep 20, 2013 11:17 am
- Zip Code: 01085
- eBay ID: havoc1482
- Tractors Owned: _______ 1948 Farmall Super A
- Circle of Safety: Y
- Twitter ID: @havoc1482
- Location: Westfield, MA
- Contact:
Re: Fuel starvation?
Okay so I got it to start but now its hunting real bad. I was tinkering with the arm and link to the carburetor, the one that crosses the front of the tractor to the governor. I did what my I&T manual said and set the throttle in wide open (Im assuming thats all the way forward aka max throttle or then I did this wrong) and adjusted the clevis "...until proper register is obtained" so the pin would just slide in freely. After I did that I got it to start but now the throttle is wacky. I set it all the way down (lever towards the seat) past the teeth on the throttle lever plate and it sounds like it did pre-teardown when I would have it at 1/4 to 1/2 throttle. I haven't even tried full throttle, I don't want to break anything.
Could this have something to do with adjusting the speed screw and spring in the governor? I haven't touched that at all.
Oh and if it means anything, as soon as I close the choke it dies.
Could this have something to do with adjusting the speed screw and spring in the governor? I haven't touched that at all.
Oh and if it means anything, as soon as I close the choke it dies.
Mike
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
- havoc1482
- 10+ Years
- Posts: 987
- Joined: Fri Sep 20, 2013 11:17 am
- Zip Code: 01085
- eBay ID: havoc1482
- Tractors Owned: _______ 1948 Farmall Super A
- Circle of Safety: Y
- Twitter ID: @havoc1482
- Location: Westfield, MA
- Contact:
Re: Fuel starvation?
Okay so I read a little farther into the manual and it said I can make it stop doing that by adjusting a bumper screw on the governor. So could this just be a matter of me tinkering with the clevis and bumper to get it to work just right?
Mike
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
- twotone
- 10+ Years
- Posts: 1189
- Joined: Sat May 14, 2011 6:09 pm
- Zip Code: 15132
- Tractors Owned: 53 F Cub
73 F Cub
53 Super A With Snow/Grader Blade
193 Plow With Colter And Jointer
144 Cultivators
22 Mower - Circle of Safety: Y
- Location: Versailles,Pa.
Re: Fuel starvation?
The bumper screw on the governor is what cured my hunting problem.
Know Your Cub, And Your Cub Will Know You.
Tom
Tom
- randallc
- Cub Pro
- Posts: 1906
- Joined: Tue Jan 18, 2011 9:16 am
- Zip Code: 72940
- Tractors Owned: 1951 Farmall Cub, 152 disk plow, 2 gang disk, belly mower, sickle mower
1949 Farmall Cub, cultivator, moldboard plow, disk,front blade. Cub Cadet, LTX1045 Mower. Cub Cadet's 109, 125, 1000, and 1250
1961 cub c2 belly mower and full blade. 48 cub manual lift with cultivators.
1947 Cub - Circle of Safety: Y
- Location: Huntington, AR
Re: Fuel starvation?
I would assume it to be a starvation problem. Need to get real good flow to the carb not just a pencil lead stream. Running with choke open is starvation. You may have something out of adjustment in carb, or seat is sticking.
-
- 10+ Years
- Posts: 2790
- Joined: Tue Jul 22, 2008 12:44 pm
- Zip Code: 48370
- Tractors Owned: 184
- Location: Oxford, MI
Re: Fuel starvation?
Perhaps I am not understanding the terminology here.
Choke closed = choke plate on carburetor covers the intake and blocks off a majority of the airflow into the carb. Used for cold starting.
Choke open = choke plate on carburetor is not covering the intake. Air flows freely into the carb. Position used for warm engine and working.
After a minute or two of running, the engine should run fine with the choke completely open. If you must keep it partially or fully closed, then there is an issue.
Choke closed = choke plate on carburetor covers the intake and blocks off a majority of the airflow into the carb. Used for cold starting.
Choke open = choke plate on carburetor is not covering the intake. Air flows freely into the carb. Position used for warm engine and working.
After a minute or two of running, the engine should run fine with the choke completely open. If you must keep it partially or fully closed, then there is an issue.
184 w/ Creeper & 3-Point
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
- havoc1482
- 10+ Years
- Posts: 987
- Joined: Fri Sep 20, 2013 11:17 am
- Zip Code: 01085
- eBay ID: havoc1482
- Tractors Owned: _______ 1948 Farmall Super A
- Circle of Safety: Y
- Twitter ID: @havoc1482
- Location: Westfield, MA
- Contact:
Re: Fuel starvation?
outdoors4evr wrote:Perhaps I am not understanding the terminology here.
Choke closed = choke plate on carburetor covers the intake and blocks off a majority of the airflow into the carb. Used for cold starting.
Choke open = choke plate on carburetor is not covering the intake. Air flows freely into the carb. Position used for warm engine and working.
After a minute or two of running, the engine should run fine with the choke completely open. If you must keep it partially or fully closed, then there is an issue.
Yes, closed as in the butterfly valve is shut, thus restricting airflow. (Thats what I meant, anyway haha) Although I currently have my choke lever disconnected so I was turning it by hand on the carb. So i might be confusing closed thinking I really opened it, but I don't think so. The point is that the engine wasn't cold when I did play with it and it has never shut off like that, especially since it wasn't at low idle.
Mike
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
- havoc1482
- 10+ Years
- Posts: 987
- Joined: Fri Sep 20, 2013 11:17 am
- Zip Code: 01085
- eBay ID: havoc1482
- Tractors Owned: _______ 1948 Farmall Super A
- Circle of Safety: Y
- Twitter ID: @havoc1482
- Location: Westfield, MA
- Contact:
Re: Fuel starvation?
Okay so, I adjusted the bumper screw, not too far in. The hunting seems to stop. In the video towards the end I turn the choke with my hand on the carb (equivalent of pushing the choke rod all the way in, to clarify) And it smooths out. Then I gave it a little throttle and it quit.
Thoughts? Maybe just wasn't warm enough for more throttle yet? It was a cold start.
Thoughts? Maybe just wasn't warm enough for more throttle yet? It was a cold start.
Mike
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
- tractordad
- 10+ Years
- Posts: 1475
- Joined: Sat Sep 12, 2009 1:36 pm
- Zip Code: 01516
- Tractors Owned: 48 Cub w/ IH C2 mower
50 High wide "demo" cub with dual fertilizer hoppers
51 high wide cub w/474 planter
62 High wide cub w/ fast hitch
72 High wide w/cultivators
75 Red Long stripe w/fast hitch & C2 mower
76 Red long stripe w/IH 1000 loader & duals
77 long stripe with IH C2 belly mower
55 Super AV w/cultivators
56 Super AV
57 130 High crop w/cultivators
1 IH 574 w IH 2250
quick hitch loader - Circle of Safety: Y
- Location: Douglas, MA
Re: Fuel starvation?
It is definitely starving for fuel. Have you taken off the fuel line at the carb to see how well the fuel flows to that point? If the flow is good to the carb, pull the carb apart again. If not, I have seen blockage in the fuel bowl on two of my SAV's. Pull the bowl, remove the shut off, and clean the bowl assembly well. It will hold contamination and restrict fuel flow. If you are running any rubber fuel line, take it off and check for blockage there.
- havoc1482
- 10+ Years
- Posts: 987
- Joined: Fri Sep 20, 2013 11:17 am
- Zip Code: 01085
- eBay ID: havoc1482
- Tractors Owned: _______ 1948 Farmall Super A
- Circle of Safety: Y
- Twitter ID: @havoc1482
- Location: Westfield, MA
- Contact:
Re: Fuel starvation?
I dont have a bowl below gas tank. PO took it off and added a fuel filter within the line with a shut off valve on the carb. Fuel flow to the carb is excellent in any case, I have no issue with it coming out when I remove the line.
So, if I have to pull the carb, what should I be looking for? I have never taken apart a carburetor and my knowledge of the parts within is very limited. I could ask a buddy of mine to look at it and lend assistance, of course hes used to car carburetors, mostly GM.
So, if I have to pull the carb, what should I be looking for? I have never taken apart a carburetor and my knowledge of the parts within is very limited. I could ask a buddy of mine to look at it and lend assistance, of course hes used to car carburetors, mostly GM.
Mike
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
-
- Team Cub Mentor
- Posts: 20369
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Fuel starvation?
He won't have a problem with the carburetor.havoc1482 wrote:I could ask a buddy of mine to look at it and lend assistance, of course he is used to car carburetors, mostly GM.
Try a container of fuel system cleaner in the gasoline. Then, not knowing which carburetor you have, remove the plug on the side or the main jet to check for fuel flow through the carburetor.
I have an excuse. CRS.
- tractordad
- 10+ Years
- Posts: 1475
- Joined: Sat Sep 12, 2009 1:36 pm
- Zip Code: 01516
- Tractors Owned: 48 Cub w/ IH C2 mower
50 High wide "demo" cub with dual fertilizer hoppers
51 high wide cub w/474 planter
62 High wide cub w/ fast hitch
72 High wide w/cultivators
75 Red Long stripe w/fast hitch & C2 mower
76 Red long stripe w/IH 1000 loader & duals
77 long stripe with IH C2 belly mower
55 Super AV w/cultivators
56 Super AV
57 130 High crop w/cultivators
1 IH 574 w IH 2250
quick hitch loader - Circle of Safety: Y
- Location: Douglas, MA
Re: Fuel starvation?
havoc1482 wrote:I dont have a bowl below gas tank. PO took it off and added a fuel filter within the line with a shut off valve on the carb. Fuel flow to the carb is excellent in any case, I have no issue with it coming out when I remove the line.
So, if I have to pull the carb, what should I be looking for? I have never taken apart a carburetor and my knowledge of the parts within is very limited. I could ask a buddy of mine to look at it and lend assistance, of course hes used to car carburetors, mostly GM.
Take pictures as you take it apart. They are very simple. Be careful to not ruin the carb gasket when you split it. The toughest part can be removing the pin holding the float in place. you want to do this so you can remove the needle valve and blow that out clean. Also, remove all the fuel mixtures screws however to put them back in as they came out, I count the number of turns to tighten the mixture screws all the way in, write it down, then disable. I clean everything with brake clean with the plastic tube on the nozzle. blow everything out with compressed air when you are done.
- havoc1482
- 10+ Years
- Posts: 987
- Joined: Fri Sep 20, 2013 11:17 am
- Zip Code: 01085
- eBay ID: havoc1482
- Tractors Owned: _______ 1948 Farmall Super A
- Circle of Safety: Y
- Twitter ID: @havoc1482
- Location: Westfield, MA
- Contact:
Re: Fuel starvation?
I took the carb apart and did a busch league cleaning. Blew some air into it, and scraped out some gunk. I took the tractor out of the garage the next day and got it down my driveway and then on my way back up it started to sputter and lose power and then quit. I'd wait 10 seconds or so and it would fire back up and I'd get it another 20 feet and I'd had to repeat the process until I got into the garage.
Is it definitely safe to say I have a fuel issue? haha
I'll plan on doing 'the works' with the carb next time around. Take it apart, get a rebuild kit, soak it, ect... the whole nine yards.
The same car guy I mentioned earlier (Mark is his name) is refurbishing the hood for a 42 John Deere LA for another buddy of his. He told me that the guy that owns the LA just rebuilt a Zenith carb for a Farmall. And since he owes Mark for doing his LAs hood, Mark will get in touch with this other guy to take a look at my carb.
Boy, it sure helps to know people.
Is it definitely safe to say I have a fuel issue? haha
I'll plan on doing 'the works' with the carb next time around. Take it apart, get a rebuild kit, soak it, ect... the whole nine yards.
The same car guy I mentioned earlier (Mark is his name) is refurbishing the hood for a 42 John Deere LA for another buddy of his. He told me that the guy that owns the LA just rebuilt a Zenith carb for a Farmall. And since he owes Mark for doing his LAs hood, Mark will get in touch with this other guy to take a look at my carb.
Boy, it sure helps to know people.
Mike
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
I bleed Black & Gold
IH Collectors Club New England (Chapter 18)
Western Mass. (The 413)
Return to “Farmall A, Super A, AV, 100, 130 & 140”
Who is online
Users browsing this forum: No registered users and 14 guests