This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Long Time reader First Time Poster
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 5
- Joined: Sun Dec 28, 2008 1:01 pm
Long Time reader First Time Poster
I have a IH 140 that I believe need a new transmission bearing and seal (27 and 25), it's for the transmission shaft (20) can't post photo that I got from Rudi.
I know that the tractor will have to be split but it appears that I might be able to get at the bearing and seal if I remove the retainer (28). Is that possable? Is the bearing pressed on the shaft?
Thanks
I know that the tractor will have to be split but it appears that I might be able to get at the bearing and seal if I remove the retainer (28). Is that possable? Is the bearing pressed on the shaft?
Thanks
-
- 10+ Years
- Posts: 588
- Joined: Mon Sep 17, 2007 9:06 pm
- Zip Code: 23069
- Location: Central Virginia
Re: Long Time reader First Time Poster
Is this the page from Rudi?
IHman61 wrote:I have a IH 140 that I believe need a new transmission bearing and seal (27 and 25), it's for the transmission shaft (20) can't post photo that I got from Rudi.
I know that the tractor will have to be split but it appears that I might be able to get at the bearing and seal if I remove the retainer (28). Is that possable? Is the bearing pressed on the shaft?
Thanks
-
- 10+ Years
- Posts: 5
- Joined: Sun Dec 28, 2008 1:01 pm
Re: Long Time reader First Time Poster
Yes that's it. Do you know if you can get to the bearing?
-
- 10+ Years
- Posts: 588
- Joined: Mon Sep 17, 2007 9:06 pm
- Zip Code: 23069
- Location: Central Virginia
Re: Long Time reader First Time Poster
No I don't about that bearing.
There are a bunch of guys like BigDog and David Bennet and Barnyard and may others that can do this stuff in there sleep. They should be able to help.
Give them a day to look over your message if no one reponds send them a PM.
There are a bunch of guys like BigDog and David Bennet and Barnyard and may others that can do this stuff in there sleep. They should be able to help.
Give them a day to look over your message if no one reponds send them a PM.
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
Re: Long Time reader First Time Poster
David Bennett will be much more familiar with the 140. I'm gonna hope he can bail you out. I can't get the image large enough for my failing eyes to see the details and numbers.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
- Team Cub
- Posts: 17272
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: Long Time reader First Time Poster
Been quite a while since I have been in one, but am about 98% certain it goes this way:
Remove the drive flange (30) then you can remove the retainer (28). The seal (27) will come off with the retainer. You knock the old seal out of the retainer after it is removed. Then you can get the bearing (25) out the front.
Remove the drive flange (30) then you can remove the retainer (28). The seal (27) will come off with the retainer. You knock the old seal out of the retainer after it is removed. Then you can get the bearing (25) out the front.
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Re: Long Time reader First Time Poster
Guys:
sorry for this one, this is one manual that I haven't resized the pics.. so it is going to be a bit on the large size.. as in size of pixels ..
It is from the purl=http://www.cleancomputes.com/Cub/Super%20A%20-%20Super%20AV/TC-39B%20Parts%20Catalog/index.html]TC-39B Parts Catalog[/url], on the Cub Manual Server..
Page 167
Item #25 IH Part # ST 246 Bearing, Ball W/Snap Ring (Transmission Spline Shaft, Front)
Item #27 IH Part # 42 177D Oil Seal, Transmission Spline Shaft
Hope this helps..
This is one manual that will need to be resized for tne new format.
sorry for this one, this is one manual that I haven't resized the pics.. so it is going to be a bit on the large size.. as in size of pixels ..
It is from the purl=http://www.cleancomputes.com/Cub/Super%20A%20-%20Super%20AV/TC-39B%20Parts%20Catalog/index.html]TC-39B Parts Catalog[/url], on the Cub Manual Server..
Page 167
Item #25 IH Part # ST 246 Bearing, Ball W/Snap Ring (Transmission Spline Shaft, Front)
Item #27 IH Part # 42 177D Oil Seal, Transmission Spline Shaft
Hope this helps..
This is one manual that will need to be resized for tne new format.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 588
- Joined: Mon Sep 17, 2007 9:06 pm
- Zip Code: 23069
- Location: Central Virginia
Re: Long Time reader First Time Poster
I sent David a PM regarding our bearing problems.
- Boss Hog
- Cub Pro
- Posts: 10290
- Joined: Mon Oct 24, 2005 8:35 pm
- Zip Code: 23962
- eBay ID: dmb2613
- Circle of Safety: Y
- Location: VA. Randolph
Re: Long Time reader First Time Poster
Sorry for the late reply, I have the flue or some type of bug that has been a bit rough on me the past two days.
The 140 front bearing can be replaced without going too deep into the trans. Take the top off the trans and put it in two gears tp get the flange bolt loose[ the 140 unlike the cub had a 2 piece main shaft..If the front bearing is bad I would check the back bearing too. the top ones go bad before the bottom ones. Just use caution just like splitting a cub. 140 is just larger. chuck the front end so it want topel over You will need a bit of help as it is much heaver than a cub.
David
The 140 front bearing can be replaced without going too deep into the trans. Take the top off the trans and put it in two gears tp get the flange bolt loose[ the 140 unlike the cub had a 2 piece main shaft..If the front bearing is bad I would check the back bearing too. the top ones go bad before the bottom ones. Just use caution just like splitting a cub. 140 is just larger. chuck the front end so it want topel over You will need a bit of help as it is much heaver than a cub.
David
IN GOD WE TRUST
All others pay cash
Boss Hog
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg
All others pay cash
Boss Hog
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg
-
- 10+ Years
- Posts: 588
- Joined: Mon Sep 17, 2007 9:06 pm
- Zip Code: 23069
- Location: Central Virginia
Re: Long Time reader First Time Poster
David Bennett wrote:Sorry for the late reply, I have the flue or some type of bug that has been a bit rough on me the past two days.
The 140 front bearing can be replaced without going too deep into the trans. Take the top off the trans and put it in two gears tp get the flange bolt loose[ the 140 unlike the cub had a 2 piece main shaft..If the front bearing is bad I would check the back bearing too. the top ones go bad before the bottom ones. Just use caution just like splitting a cub. 140 is just larger. chuck the front end so it want topel over You will need a bit of help as it is much heaver than a cub.
David
Thanks David,
what do you mean by "two gears tp"?
Hope your feeling better.
-
- 10+ Years
- Posts: 47
- Joined: Sun Nov 04, 2007 2:53 pm
- Zip Code: 22728
- Location: VA, Midland
Re: Long Time reader First Time Poster
Mark In Richmond wrote:David Bennett wrote:Sorry for the late reply, I have the flue or some type of bug that has been a bit rough on me the past two days.
The 140 front bearing can be replaced without going too deep into the trans. Take the top off the trans and put it in two gears tp get the flange bolt loose[ the 140 unlike the cub had a 2 piece main shaft..If the front bearing is bad I would check the back bearing too. the top ones go bad before the bottom ones. Just use caution just like splitting a cub. 140 is just larger. chuck the front end so it want topel over You will need a bit of help as it is much heaver than a cub.
David
Thanks David,
what do you mean by "two gears tp"?
Hope your feeling better.
Mark,
I think he meant "two gears to get the flange bolt loose", speaking of moving the sliders on the top shaft to lock into two gears at once so you can remove the flange bolt (7/16 bolt on the end of shaft #20, not pictured) without the shaft moving on you. David, hope you're feeling better soon. I'm sitting here with laryngitis for the 2nd day, so I feel for you!
52 Super M, 53 Super H, 52 Super C, Wheel horse C101, JD 140.
-
- 10+ Years
- Posts: 588
- Joined: Mon Sep 17, 2007 9:06 pm
- Zip Code: 23069
- Location: Central Virginia
Re: Long Time reader First Time Poster
Stan and David
Happy New and I hope you, David, are feeling better.
I got the 140 split. Everyting went smooth except for the key. That was a pain.
I agree that the upper rear bearing should also be replaced.
Is that pressed in. How do I get it out?
It appears that a snap ring holds the back gear. Do I remove that and pull the shaft? Or do I remove the 90 degree pulley and pull it out through the rear of the trans??
Thanks for all your help.
Happy New and I hope you, David, are feeling better.
I got the 140 split. Everyting went smooth except for the key. That was a pain.
I agree that the upper rear bearing should also be replaced.
Is that pressed in. How do I get it out?
It appears that a snap ring holds the back gear. Do I remove that and pull the shaft? Or do I remove the 90 degree pulley and pull it out through the rear of the trans??
Thanks for all your help.
-
- 10+ Years
- Posts: 697
- Joined: Sun Mar 04, 2007 10:16 pm
- Zip Code: 52742
- Tractors Owned: Check out my signature!
- Circle of Safety: Y
- Location: IA, DeWitt
Re: Long Time reader First Time Poster
IHman61. Welcome aboard.
Red56.
Red56.
Tractors in the stable: '62 560D Cub Cadets in the stable: 782D, 1572 SGT, 1772 SGT, 1782 SGT
-
- 10+ Years
- Posts: 5
- Joined: Sun Dec 28, 2008 1:01 pm
Re: Long Time reader First Time Poster
Thanks looks like we will get it fixed later this month.
Return to “Farmall A, Super A, AV, 100, 130 & 140”
Who is online
Users browsing this forum: No registered users and 9 guests