Farmall 100, 1954 - 1973
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds
or one of our site sponsors for your tractor and parts needs.
Wed Mar 16, 2011 5:38 am
Became the proud owner of a 100 Farmall yesterday. It has a one point fast hitch with cultivator, planter, double gang disk,grader blade,bushhog, 2 disk breaker, boom pole, middle buster. It is a 2 owner tractor in pretty good shape.
Now for the problem. The battery was completely dead and after we put a new battery in it the generator would not charge (6 volt) was told it needed to have the generator excited. Can anyone tell me how to do this or if it needs it or do I just need to have the generator rebuilt?
The owner said it was charging when he parked it last fall.
Also need some help on what the equipment might be worth. Will probably sell all but the cultivator and maybe the breaking plow. It was all bought when the tractor was bought new.
Wed Mar 16, 2011 6:57 am
Did you install the battery positive ground? (correct way)
Last edited by danovercash
on Wed Mar 16, 2011 10:53 am, edited 1 time in total.
Wed Mar 16, 2011 7:02 am
Guy I bought it from said to put the hot cable to the ground post on battery and ground cable to hot post. That is the way I hooked it up. Is this right?
Wed Mar 16, 2011 8:57 am
Positive post on the battery to the ground cable and negative post to the other cable. Touch a jumper wire from the Batt. terminal on the regulator to the Gen terminal on the regulator. That will polarize it.
Wed Mar 16, 2011 6:17 pm
Jumped from the batt terminal to the gen terminal but I think it is still discharging. The guage shows discharge but it is very slightly to the discharge side. It has a brand new 6 volt battery. Any other suggestions? Could the guage be wrong? It is just barley off the 0 toward discharge.
When I touched the gen terminal with the jumper I got a pretty good spark.
Wed Mar 16, 2011 6:21 pm
Take a jumper wire and connect it to the F terminal of the generator and then to ground. If it charges then, your generator is working and the problem is likely with the regulator or connections.
If it does not charge with the generator F terminal grounded the problem is with the generator.
Is your generator belt good and tight?
Wed Mar 16, 2011 7:22 pm
thanks Bigdog I will try that tomorrow. Do I need to ground to the tractor or back to ground on battery
Wed Mar 16, 2011 8:16 pm
Ground to good clean metal surface on the tractor. Going clear back to the battery isn't necessary but it works too.
Thu Mar 17, 2011 5:25 am
Engine RPM's above idle? Generater may not be turning fast enough.
Thu Mar 17, 2011 2:49 pm
Took the generator off and carried it and had it checked. It checked good. The wires look good and I tighten the fan belt just in case. They said it was probably the regulator,is there a way to check it?
Thu Mar 17, 2011 3:24 pm
You can remove the cover and see if the cutout relay is pulling in. You can also check and clean the contacts. Beyond that, everything is pretty much hit and miss unless you have the right tools to do the job.
Did the generator charge with the F terminal grounded? If not, you still have a wiring problem.
Thu Mar 17, 2011 5:39 pm
I couldn't get it to charge by grounding the f terminal. I am getting fire out of the regulator to the generator.
Thu Mar 17, 2011 7:09 pm
If the generator does not charge with the F terminal grounded but checked OK at the shop I suspect you are not getting a good ground through the generator mounts. Clean up the contacting surfaces on the generator flanges and mounting bracket or run a ground wire from the generator body to a good ground source.
Please explain "I am getting fire out of the regulator to the generator."
Thu Mar 17, 2011 7:39 pm
I accidentally touched the terminal (A terminal think) on the regulator, side with the one wire with a screwdriver and it sparked.
Thu Mar 17, 2011 7:47 pm
Running or not running when this happened?
Powered by phpBB © phpBB Group.
phpBB Mobile / SEO by Artodia.