Switch to full style
Farmall C & Super C Tractors, 1948-1954

Forum rules

Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Post a reply

Calling All Super C and Super A Owners

Mon Aug 15, 2011 7:36 pm

I have two questions for you folks. I am contemplating removing and cleaning the oil strainer on my Super C Touch Control in the near future. Does anyone have any tips or suggestions for the job? There's not much about it in the manuals.

Second question. Does anyone have a C-123 engine equipped with an oil dipstick? Mine does, but the engine is a former power unit engine. See the photo below. The dipstick on mine reads the oil level way wrong and I think it's a result of an incorrect dipstick/oil pan combination. Can you post some photos of what you have? Thanks.

Image

Re: Calling All Super C and Super A Owners

Mon Aug 15, 2011 9:49 pm

Working with the strainer on the touch control is pretty much the same deal as with a Cub, except you have the luxury of removing it without any major teardown. It'll probably be crushed, just like the Cub strainer usually is. If it was me I would take it out, clean it in kerosene, etc. and put it back in. Long as it remains a closed system I don't think the strainer's that important to start with.

That dipstick doesn't look like anything I've seen before, but since it's a power unit engine, who knows. It is in the right place though. You need a dipstick from a 200, 230, etc.

Al

Re: Calling All Super C and Super A Owners

Tue Aug 16, 2011 7:41 am

Don, I have the dipstick on my SA and will photograph and measure it today. Then I will post for you (along with the long-awaited info on the oil pan!).

Oil dipstick:
Image
Image

Old filter...you do not have to remove the bottom plate...I already had it off the tractor:
Image
Image

Replaced the broken one with one from my other TC
Image

Dale F

Re: Calling All Super C and Super A Owners

Tue Aug 16, 2011 7:56 am

Thanks, Al & Dale. Great responses. I hope I don't have to buy a new strainer. They're pretty pricey at $85. :shock:

Re: Calling All Super C and Super A Owners

Tue Aug 16, 2011 1:59 pm

That dipstick is one like on my 140's. I will have to double check the Super A's and 100's to see what they have. It is possible that Dale's is an engine from a later model tractor. I have also seen dipsticks like yours before Don, but can't recall where or what it was on. I will have to double check.

Re: Calling All Super C and Super A Owners

Tue Aug 16, 2011 11:23 pm

Don, my engine was apparently changed out at some point because it is a 123 with no serial number. The dipstick is listed in the parts manual for the 123 engine. Here are some photos:

Image
ONE SIDE OF DIPSTICK:
Image
OPPOSITE SIDE OF DIPSTICK:
Image

Hope this helps.

Dale F
Last edited by Dale Finch on Wed Aug 17, 2011 8:30 am, edited 2 times in total.

Re: Calling All Super C and Super A Owners

Wed Aug 17, 2011 6:05 am

That helps a lot, Dale. I wish I could find the parts for the type dipstick you have. Thanks.

Re: Calling All Super C and Super A Owners

Wed Aug 17, 2011 6:41 am

Just out of my curiosity, your tractor has a power unit engine with an oil dipstick, and the oil pan petcocks? Maybe the petcocks couldn't be used on a power unit due to the shroud or mounting frame? I get asked often, where's the dip stick on my SC. 8)

Re: Calling All Super C and Super A Owners

Wed Aug 17, 2011 7:22 am

Harold,

There are currently no petcocks in my oil pan. However, there are two threaded holes with pipe plugs in them where the petcocks would go. I'm guessing that the original power unit oil pan was much deeper than the one on a 123 installed in a tractor. If I can't find the correct dipstick parts for my oil pan, I will revert to the petcocks.

Re: Calling All Super C and Super A Owners

Wed Aug 17, 2011 8:28 am

I would agree Don, that most likely the power unit oil pan was removed and the tractor oil pan installed when the engine was installed. I don't know what the difference between them would be. I imagine that when they did the swap they decided petcocks and a dipstick were redundant and opted for the dipstick. However, the dipstick is probably only accurate with the power unit oil pan in place.

Re: Calling All Super C and Super A Owners

Wed Aug 17, 2011 8:49 am

Don,
Not sure if this helps, and I can't beleve that Wenger's has something somewhat reasonably priced, but here ya go:

http://www.wengers.com/parts/Farm-Tract ... 62611R.htm

Re: Calling All Super C and Super A Owners

Wed Aug 17, 2011 12:39 pm

That certainly looks like it!

Dale F

Re: Calling All Super C and Super A Owners

Wed Aug 17, 2011 7:43 pm

Bill,

Thanks. I'll be on the phone tomorrow morning. There is another part that goes with the dipstick, so I'll see if they have that, too.

Believe it or not, every once in a while Wenger's has something for a reasonable price. I got a complete colter for the Cub fast hitch plow for $50 a couple of years back.

Re: Calling All Super C and Super A Owners

Thu Aug 25, 2011 11:28 am

To update everyone, I have the parts I need to convert from the power unit dipstick to the tractor dipstick. I'll post a photo after it's finished.

Re: Calling All Super C and Super A Owners

Thu Aug 25, 2011 12:38 pm

the 123 i have in my 240U has the dipstick in the 'more normal' centered location on the block, as i recall.
Post a reply