I was worndering if there is a way to take up the front wheel play on our BN. I know there will be some slight play with my steering universal not being tight Can I tighten the cap and push the worm gear forward?
Thanks Phil
Front Wheel play
Moderator: Team Cub
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
5 posts
• Page 1 of 1
Front Wheel play
by Phillip W. Lenke » Tue Aug 08, 2006 12:17 pm
"Work Hard ,Play Often,Care Always"
- Phillip W. Lenke
- 5+ Years
- Posts: 1479
- Joined: Wed May 25, 2005 1:21 pm
- Zip Code: 43449
by KETCHAM » Sat Aug 26, 2006 6:46 pm
???slop in the wheels,gear box or tie rods?My H has to get new wheel bearings.My 49 cub Ollie Needs a little of everything.Had front end up off the groud yet?KETCHAM much slack in u-joint?
47 CUB[Krusty] 49 CUB[Ollie] 50 H-- PLOWS DISCS MOWERS AND lots more stuff!!Life is to short -Have fun now cause ya ain't gonna be here long!!!!
-
KETCHAM - 5+ Years
- Posts: 5511
- Joined: Thu Jul 28, 2005 2:37 pm
- Location: Marshallville Ohio
- Zip Code: 44645
- eBay ID: kevinb2366
- Tractors Owned: 47 Cub 48 Cub 50 H
by WKPoor » Wed Sep 13, 2006 10:46 pm
Ketchup, I can't speak for the BN but the H you mentioned I can say a few words. I'll bet 99 out of a 100 H's or M's have the upper and lower bolster bushings plum wore out. Easy check- jack up the front end off the frame rails and grap the lower bolster and jerk it around. Bet you find it loose as a goose! Thats why they shutter going down the road in high gear. I bought the bushings for mine to install hopefully in my life time 
- WKPoor
- 5+ Years
by KETCHAM » Thu Sep 14, 2006 6:51 am
I'M SURE YOU ARE RIGHT.I'M WAITING TO GET A JOB[NEED MONEY] FOR FRONT TIRES.WHEN I DO THEM I'LL CHECK THE BEARINGS AND BUSHINGS.A PAINT JOB IS IN ORDER ALSO FOR THE WHEELS AND HUBS.THANKS KETCHAM
47 CUB[Krusty] 49 CUB[Ollie] 50 H-- PLOWS DISCS MOWERS AND lots more stuff!!Life is to short -Have fun now cause ya ain't gonna be here long!!!!
-
KETCHAM - 5+ Years
- Posts: 5511
- Joined: Thu Jul 28, 2005 2:37 pm
- Location: Marshallville Ohio
- Zip Code: 44645
- eBay ID: kevinb2366
- Tractors Owned: 47 Cub 48 Cub 50 H
by Phillip W. Lenke » Thu Sep 14, 2006 8:14 am
I went through the bearings and bushings with the same effect.
Is there aa adjustment that can be made to the steering splone.
The BN has a cub that holds the shaft in place. I was wondering by tightening the cup if this would do it.
Phil
Is there aa adjustment that can be made to the steering splone.
The BN has a cub that holds the shaft in place. I was wondering by tightening the cup if this would do it.
Phil
"Work Hard ,Play Often,Care Always"
- Phillip W. Lenke
- 5+ Years
- Posts: 1479
- Joined: Wed May 25, 2005 1:21 pm
- Zip Code: 43449
5 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 1 guest
|
|