To All,
Need help with the dimensions for the Brinly Lift rod and the placement of the holes for pins and cotter pins.
Thanks!
Froghunter
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Brinly Lift Rod Dimension
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- Froghunter
- 10+ Years
- Posts: 289
- Joined: Tue Jan 08, 2008 9:51 pm
- Zip Code: 19938
- eBay ID: bull829
- Location: The First State (Clayton)
Brinly Lift Rod Dimension
3 x CCO
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
- wdeturck
- 10+ Years
- Posts: 949
- Joined: Mon Dec 08, 2003 6:15 am
- Location: PA Oakmont 15139
Re: Brinly Lift Rod Dimension
Froghunter: What Brinly lift rod? The only lift bars I know of are the 2 that may have 3 holes and be slotted used on the sleeve hitch.
The Geezer from IHregistry.com which crashed and is now Cub Cadet Collectors.
- Froghunter
- 10+ Years
- Posts: 289
- Joined: Tue Jan 08, 2008 9:51 pm
- Zip Code: 19938
- eBay ID: bull829
- Location: The First State (Clayton)
Re: Brinly Lift Rod Dimension
Bill,
The one below, but with out the two holes. I need to make Four of them. One each for the CC 104, 106 , 1450 and CCO.
Thanks!
Froghunter
The one below, but with out the two holes. I need to make Four of them. One each for the CC 104, 106 , 1450 and CCO.
Thanks!
Froghunter
3 x CCO
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
- wdeturck
- 10+ Years
- Posts: 949
- Joined: Mon Dec 08, 2003 6:15 am
- Location: PA Oakmont 15139
Re: Brinly Lift Rod Dimension
The picture you have is a universal lift pin made by Jim Steel about 10 years ago. The lift pins were suppose to stay with the implements. The universal pin has 2 indexing holes as the Tiller uses the hole vertically and most of the rest use the hole indexed horizontally. The ones for the Originals use the bottom left hole for the cotter pin and don't have indexing holes(THe top casting isn't drilled like the rest of the Cub Cadets). Some pins have the washers weded on them and some don't. All the 3/16" cotter pin holes on the left end of the pin must be close enough to the end to let those pins turn 360 without binding. E-mail me and I will send you of one with dimensions on it.
The Geezer from IHregistry.com which crashed and is now Cub Cadet Collectors.
- Froghunter
- 10+ Years
- Posts: 289
- Joined: Tue Jan 08, 2008 9:51 pm
- Zip Code: 19938
- eBay ID: bull829
- Location: The First State (Clayton)
Re: Brinly Lift Rod Dimension
Geezer,
email send!
Froghunter
email send!
Froghunter
3 x CCO
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
- Froghunter
- 10+ Years
- Posts: 289
- Joined: Tue Jan 08, 2008 9:51 pm
- Zip Code: 19938
- eBay ID: bull829
- Location: The First State (Clayton)
Re: Brinly Lift Rod Dimension
3 x CCO
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
- wdeturck
- 10+ Years
- Posts: 949
- Joined: Mon Dec 08, 2003 6:15 am
- Location: PA Oakmont 15139
Re: Brinly Lift Rod Dimension
Hi Frog Hunter: Just to busy to keep up with my E-mail and forums. I will send the picture with the dimensions. I did look at one of my other pins yesterday and it is like the one I will E-mail you the picture. I'm guessing but the lift pins with the washers welded on are from Brinly. if it has the cotter pin hole about 1/8" from the front end then it's for an Original. It may or may not have the 3/16" indexing hole used on the NF & WF. the indexing hole is used to set the rear holes Horizontal(most implements) or Vertical for the Tiller. the washer welded on is needed on the CCO as it keeps the pin from rubbing on the casting. only weld that washer to the pin on the rear side of the washer as it will interfere with the dimension to the rear hole and/or the indexing hole.
Those pins were supplied with the implements and not the 3 point hitches but are usually left in the tractor so they get lost from the implement.
Those pins were supplied with the implements and not the 3 point hitches but are usually left in the tractor so they get lost from the implement.
The Geezer from IHregistry.com which crashed and is now Cub Cadet Collectors.
- Froghunter
- 10+ Years
- Posts: 289
- Joined: Tue Jan 08, 2008 9:51 pm
- Zip Code: 19938
- eBay ID: bull829
- Location: The First State (Clayton)
Re: Brinly Lift Rod Dimension
Geezer,
Thanks got the e-mail and later today I will post the picture for others!
Froghunter
Thanks got the e-mail and later today I will post the picture for others!
Froghunter
3 x CCO
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
- Froghunter
- 10+ Years
- Posts: 289
- Joined: Tue Jan 08, 2008 9:51 pm
- Zip Code: 19938
- eBay ID: bull829
- Location: The First State (Clayton)
Re: Brinly Lift Rod Dimension
3 x CCO
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
CC106
CC1450 (Donated to School to use)
CC104
Case 644 Compact Loader
Case/IH 235
Who is online
Users browsing this forum: No registered users and 5 guests