This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Red Series 1282 Stored for 15 Years
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
I suspect that due to the design of the auger, it is being forced to one side or the other during operation which is causing it to bind up. You may not be able to move sideways by hand but under power and under load perhaps it will. Can you have someone else run it while you look to see if you can find where the noise is coming from. One thing for sure - if you keep running it until it breaks real good, you'll find the problem.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
- 10+ Years
- Posts: 2338
- Joined: Sat Apr 10, 2004 6:12 pm
- Zip Code: 40218
- Circle of Safety: Y
- Location: KY, Louisville
Since you never said what model snowthrower you have, I assume it is a Model QA36B, since it was built from 1980 and later and would be correct for a 1282. I'm not sure what you are calling a "shear pin" or "drift pin", since there are none in the design. There is a 1/4" x 1-1/4" coiled spring pin (spriol pin) for the small sprocket if that is the one you mean, and if it is being replaced with anything else ( roll pin, bolt, solid pin etc), it will probably continue to break. The spriol pins are designed to take some shock without breaking that a common roll pin, bolts etc will not.
The shaft the small sprocket is on is mounted in needle bearings in the casting, and that casting has two bolts (1/2" I think) that adjust the tension of the roller chain to the auger. Since you say there is no noise when "the shear pin is broken", look at the adjustment area/casting for something broke, misaligned, or needle bearing problems, chain/chain adjustment. If not, then there is most likely an auger bearing/alignment problem.
The shaft the small sprocket is on is mounted in needle bearings in the casting, and that casting has two bolts (1/2" I think) that adjust the tension of the roller chain to the auger. Since you say there is no noise when "the shear pin is broken", look at the adjustment area/casting for something broke, misaligned, or needle bearing problems, chain/chain adjustment. If not, then there is most likely an auger bearing/alignment problem.
-
- Cub Pro
- Posts: 2575
- Joined: Mon Feb 03, 2003 5:25 am
- Zip Code: 37774
- Tractors Owned: 1948 McCormick-Deering Farmall Cub
152 Disc Plow & Flat Belt Pulley
Brinly #8 Moldboard Plow
1971 JD 112 Garden Tractor
1928 Economy Hit & Miss Engine
1927 David Bradley "Little Wonder" Feed Grinder
1 A.H. Patch Corn Shellers
1 A.H. Patch #1 Grist Mill - Circle of Safety: Y
- Location: TN, Loudon (near Knoxville)
Hey Keith: If it were me...I'd check the bearings good. If there's any wear...replace them. You can probably go to NAPA with them first to see if they have a new set (before going to Case/ IH).
If they're good...repack them with grease before putting them back in your snow blower. The NEW ones sold today are more than likely sealed bearings that will run smoother and never need to be repacked.
If they're good...repack them with grease before putting them back in your snow blower. The NEW ones sold today are more than likely sealed bearings that will run smoother and never need to be repacked.
"Save The Possums...Collect The Whole Set"
"Tennessee Sun-Dried Possum...Heaven In A Can"
"Tennessee Sun-Dried Possum...Heaven In A Can"
- beaconlight
- 10+ Years
- Posts: 7703
- Joined: Thu Aug 19, 2004 2:31 pm
- Zip Code: 10314
- Location: NY Staten Island & Franklin
Don't believe that never need repack stuff. Use a hypodrmic to push new clean grease into one of them. There are comercial grease insertion tools for them also. this is a case of where a diabetic in the family helps.
Bill
Bill
Bill
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
- John *.?-!.* cub owner
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Who is online
Users browsing this forum: No registered users and 6 guests