IHC Cub Cadet Forum -- Questions and answers to all of your Cadet related issues.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds
or one of our site sponsors for your tractor and parts needs.
Wed Dec 01, 2010 9:17 pm
I have recently purchased a nice collection, including a 107, snow thrower, tiller and mower deck. Since snow is just around the corner I wanted to sand down the rust on the single stage snow thrower and then paint it. Can anyone tell me how to get the auger out? Looks to be a trick to working it out. Thanks for your help.
Wed Dec 01, 2010 9:48 pm
G'day, welcome and congrats
on acquiring the 107 and the QA42. My buddy Gord just totally rebuilt his QA-36 .. it is a beaut
Check you email ok
Suggest you have a look at the links below, there are some good resources available to our members. Although we do not have a lot of stuff on Cub Cadets yet, many of us do own them and there are guys chock full of good info on them available to you.
Enjoy your new toys
Fri Dec 03, 2010 7:48 pm
Thanks Rudi. I did get the manuals via email.
Sat Dec 04, 2010 5:05 pm
I would like to get a copy of the manual too, please.
Sat Dec 04, 2010 6:14 pm
Nice to see you posting again...
You have been lurking for a while huh
Sat Dec 04, 2010 6:58 pm
I come here often Rudi.
It is one of my favorite places to visit.
Great folks here!
Just bought a snow thrower, haven't picked it up yet.
Sat Dec 04, 2010 7:19 pm
I think you will like the thrower. Gord is raring to go with his. Got new turf tires for the 108 last week so he is just waiting for snow to come and stay.
Sat Dec 04, 2010 8:53 pm
Here is how I slipped the auger out of my snow thrower so I can sand all and paint. I released the chain tention and then pulled the clevis pin to give even more slack. I secured the port side to a pole in my garage and used a come-a-long on the starborad side to ease the sides out just a quarter inch or so. The auger came right out very easily. I power sanded the inside and various parts and got a coat of primer on. Heading to Tractor Supply tomorrow to pick put the paint. Need to get this done and back together before the snow flies!
Mon Dec 06, 2010 6:06 pm
Don't they offer special paint for snowblowers so the snow can't / won't freeze to the cold metal? I been using PAM or any other non stick spray. It seems to me when the sun goes down and the temp drops the blower auger seems to always freeze up at this time. Maybe its the dew point that causes this.
Mon Dec 06, 2010 9:11 pm
I am looking for any tips on using the snow thrower.
I will be mounting it on my 149 and putting chains on.
The snow here can be dry powder, or heavy and wet, or a granular mix with sleet, in other words just about any type is possible.
What can I expect from the snow blower?
Mon Dec 06, 2010 10:01 pm
That snow blower on a 149 is a great setup. I had the same setup here in Buffalo, NY for many years. I could easily throw snow onto my neighbors driveway, about 40-feet away. The wet/heavy stuff can be a bit of a pain. I used to spray mine down with Armorall or Silicone if we had the wet stuff, and it seemed to keep it moving rather than pack up. The paint that you can get is graphite paint called Slip Plate. Case/New Holland makes it, and it works pretty good. I've used it on mower decks, and it does seem to keep grass from sticking. I know that some of the commercial mowing companies like Exmark and Ferris make teflon paint for mower decks, and I would think that it would work good too.
Tue Dec 07, 2010 5:30 pm
You don't see many snow blowers around here.
Some years we have almost no snow, some years we get 2 to 3 feet at a time.
I don't like plowing much, the piles are a mess and with deep snow you can only push so much before you have nowhere to push it anymore.
Looks like fun
, unless the wind blows it back in your face
Tue Dec 07, 2010 8:43 pm
EZ Slide is the graphite paint I pruchased from Trarctor Supply. This is a pretty interesting paint. It has a ton of graphite in it and puts an very slick gray coat on the surface. It is very slick and I think it will work great. This stuff goes a long ways so just buy a quart! Also it may not be in the paint section of TSC, it may be over in the power take-off parts for some reason.
Powered by phpBB © phpBB Group.
phpBB Mobile / SEO by Artodia.