This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Cadet Original axle seal
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- jostev
- 10+ Years
- Posts: 1254
- Joined: Wed Aug 31, 2005 5:10 pm
- Zip Code: 03574
- eBay ID: farmallkid48
- Skype Name: farmall_kid
- Tractors Owned: 41 B
48 H
49 C
50 red demo Cub
51 C
52 Cub
54 Super C
61 and 63 Cub Cadet Originals
78 Cub Cadet 1450
73 154 lo-boy - Location: NH, Bethlehem
- Contact:
Cadet Original axle seal
I have a 1962 Cub Cadet Original that must have a bad seal on the right side sitting on it. How do I go about changing it? thanks for any advice, Jostev
70 Brockway 361
http://photobucket.com/albums/c47/jostev/
http://photobucket.com/albums/c47/jostev/
- wdeturck
- 10+ Years
- Posts: 949
- Joined: Mon Dec 08, 2003 6:15 am
- Location: PA Oakmont 15139
Jostev.: You have the easy side. Take the the 5 bolts off the axle housing and pull the housing and axle together. the grease seal is in the differential housing. seal part # IH-610465-c 91. You might want to check the axle bushing(IH-376160-R1) while you have it apart. Just take the snap ring off and pull the axle. The left side has the brake to mess with.
I just got the prise and there is a number change. from R91 to R-92
IH-376160-R1 BUSHING 18.23
IH-610465-C91 USE IH-610465-C92 10.13
I just got the prise and there is a number change. from R91 to R-92
IH-376160-R1 BUSHING 18.23
IH-610465-C91 USE IH-610465-C92 10.13
Last edited by wdeturck on Mon Oct 10, 2005 7:17 pm, edited 1 time in total.
The Geezer from IHregistry.com which crashed and is now Cub Cadet Collectors.
- jostev
- 10+ Years
- Posts: 1254
- Joined: Wed Aug 31, 2005 5:10 pm
- Zip Code: 03574
- eBay ID: farmallkid48
- Skype Name: farmall_kid
- Tractors Owned: 41 B
48 H
49 C
50 red demo Cub
51 C
52 Cub
54 Super C
61 and 63 Cub Cadet Originals
78 Cub Cadet 1450
73 154 lo-boy - Location: NH, Bethlehem
- Contact:
thanks for such a quick reply, would that number/numbers work for a cub cadet dealer? the cadet dealer is closer than the closest IH dealer-2-3 hours. thanks, I will get to it in a few days. thanks again, jostev
70 Brockway 361
http://photobucket.com/albums/c47/jostev/
http://photobucket.com/albums/c47/jostev/
- wdeturck
- 10+ Years
- Posts: 949
- Joined: Mon Dec 08, 2003 6:15 am
- Location: PA Oakmont 15139
I just edited the post. I got the wrong seal number. Use the numbers by the price I added. You can get them at a cub dealer, IH dealer and maybe a Case dealer. I can give yoy the phone number of a good dealer in WI that will have it and ships every day. Madson's Service Inc. 1-920-773-2661.
The Geezer from IHregistry.com which crashed and is now Cub Cadet Collectors.
- jostev
- 10+ Years
- Posts: 1254
- Joined: Wed Aug 31, 2005 5:10 pm
- Zip Code: 03574
- eBay ID: farmallkid48
- Skype Name: farmall_kid
- Tractors Owned: 41 B
48 H
49 C
50 red demo Cub
51 C
52 Cub
54 Super C
61 and 63 Cub Cadet Originals
78 Cub Cadet 1450
73 154 lo-boy - Location: NH, Bethlehem
- Contact:
Thanks, I have a Cadet dealer about a half an hour away buty the Case/IH Dealer is quite far. Thanks again, I will probably take it apart in a few minutes. thanks, Jostev
70 Brockway 361
http://photobucket.com/albums/c47/jostev/
http://photobucket.com/albums/c47/jostev/
- jostev
- 10+ Years
- Posts: 1254
- Joined: Wed Aug 31, 2005 5:10 pm
- Zip Code: 03574
- eBay ID: farmallkid48
- Skype Name: farmall_kid
- Tractors Owned: 41 B
48 H
49 C
50 red demo Cub
51 C
52 Cub
54 Super C
61 and 63 Cub Cadet Originals
78 Cub Cadet 1450
73 154 lo-boy - Location: NH, Bethlehem
- Contact:
I have another question, I got the axle and parts apart but the old seal doesn't want to come out, I was hitting it pretty hard but I don't want to break anything, any Ideas or tricks on how to get this out? Thanks for any acvice, Jostev
70 Brockway 361
http://photobucket.com/albums/c47/jostev/
http://photobucket.com/albums/c47/jostev/
- wdeturck
- 10+ Years
- Posts: 949
- Joined: Mon Dec 08, 2003 6:15 am
- Location: PA Oakmont 15139
The seal is in the transmission case and should pop right out of there with a large screwdriver or pry bar. use a block of wood under it so the seal can move out. You can try putting two self tapping screws in the seal across from each other and pry on those with a claw hammer or crow bar. They also have a seal removal tool that hooks behind the seal and is "L" shaped so you can hit it with a hammer. Good luck
The Geezer from IHregistry.com which crashed and is now Cub Cadet Collectors.
- jostev
- 10+ Years
- Posts: 1254
- Joined: Wed Aug 31, 2005 5:10 pm
- Zip Code: 03574
- eBay ID: farmallkid48
- Skype Name: farmall_kid
- Tractors Owned: 41 B
48 H
49 C
50 red demo Cub
51 C
52 Cub
54 Super C
61 and 63 Cub Cadet Originals
78 Cub Cadet 1450
73 154 lo-boy - Location: NH, Bethlehem
- Contact:
thanks, i just kept hitting it and it finally popped out, thanks again, those are rather expensive from a site that i was looking at, the buchings were up there too, only need to replace one side for now. LOL i'm very cheap.
70 Brockway 361
http://photobucket.com/albums/c47/jostev/
http://photobucket.com/albums/c47/jostev/
- John *.?-!.* cub owner
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
- jostev
- 10+ Years
- Posts: 1254
- Joined: Wed Aug 31, 2005 5:10 pm
- Zip Code: 03574
- eBay ID: farmallkid48
- Skype Name: farmall_kid
- Tractors Owned: 41 B
48 H
49 C
50 red demo Cub
51 C
52 Cub
54 Super C
61 and 63 Cub Cadet Originals
78 Cub Cadet 1450
73 154 lo-boy - Location: NH, Bethlehem
- Contact:
thanks john, I will try that next time on the other side, the only thing is that you have to take the shaft out just to get to the seal. But thatnks anyways, i will try that on other stuff when needed. Jostev
70 Brockway 361
http://photobucket.com/albums/c47/jostev/
http://photobucket.com/albums/c47/jostev/
Who is online
Users browsing this forum: No registered users and 4 guests