Farmall Cub

Well a few weeks ago with some help from Bigdog I finally got my coal, or at least enough for a couple of years for me. I was up Bigdogs way and we went over to Amanda, Ohio and got a pickup load for my shop. The guy that sold it to me is still trying to figure out why a guy from Ga would drive to Ohio to get coal mined in Ky. It'll be something to talk about for a while!!
Sure makes a good warm stove to sit by while working on Cub projects!!



Thanks Bigdog & Bossdog (cookies were great!!!!!)

Hi Ron

I finally got my coal last week. I was only able to get a half ton in my four cylinder ranger. I think its pretty neat to burn a "rock." My little brother stoped by yesterday said boy its warm in here I looked and it was 76. I am still geting used to burning it. My stove has a door vent with a bi-metal coil to regulate heat. But the coal in the back goes out. So I have been closing the vent and have to crack the ash tray so the air comes up from the bottom and will burn eavenly. Its gone wild once or twice. But I'm learning.

Billy

Takes a little getting used to but what my grandfather taught me came back once I started messing with it, but not before I had a cherry red top on the stove a time or two I open the bottom for a draft and adjust the damper as needed to regulate the heat. Burns real evenlso far.

Ron

Thanks for the info Ron

I have a 7"x12" flue chiminy. The gas hot water heater and furnance use it too. Seems when the furnance kicks on I loose draft to the coal and if its low it goes out. Unlike wood which it didn't bother. Starting now when I bank it for the nite I put wood on the right side and coal on the right if it goes out the wood will relight it. I should have replaced the furnance two years ago with a high efficency furnance that does nto need a chimney mine is shot just not in the budget. I need to get the lister going and see how much heat I get out of it. Hopefully between that and the wood/coal stove I will not need a furnance.

I haven't forgot about your spacers. My brother has been too busy at work and his projects. And I do not think I can cut it off strait with my old cutoff band saw.

Billy

Billy:

I have a 7"x12" flue chiminy. The gas hot water heater and furnance use it too.

I used to have a shared chimney flue with my wood furnace and my propane back-up. Was up to code at one time, but about 10 years ago, they made me separate them -- new propane installation. Also checked with my insurance and the fire marshall and building inspectors... NLC -- No Longer Code..

I would check with your local authorities... and your insurance agent. Best to know before something happens.. Here they seemed worried about blowback and excess infiltration of exhaust gases....

I never had a problem, but hey... to keep it legal, had to change it....

And, since I built a surround around my exterior chimney, I have better flue temps, no creosote buildup, no blow back problems at all. Works good!

Thanks Rudi

I have always been a put it together and try it kinda guy. If it don't work go back and find out what I overlooked. I am not very smart but feel I make up for it in common sense. I do not know the math to figure out stuff but am very confindent in finding feeling my way through in a real world mechinal way. My little brother was over yesterday. Figuring out pulley size for the engine and generator using pie. Then went back figured it at belt speed inches per second at the engine and generator. I thought it was pretty neat waching him do it.

Billy

Billy:

Anybody who can do the stuff you can do, well... that says a lot right there. Besides... to me smart means natty as in a dresser... intelligence, now that is something else. There is book smarts, and real world smarts, book learnin and life's learnin...... all are good in their own right, but the first without the second is only half smart .

My Father-in-law God Bless him, is one of the smartest, most inventive able persons that I have ever met. Due to growing up in hard scrabble times, in the depression, and being one of the strongest in the family, he got to go to school for all of 3 months or so. Can't read a word, but boy, can he figger.... the stuff he can do is amazing.

He is an icon of real world smarts... we need people like him to make sure the world is a balanced place.

And, don't denigrate yourself... you are a pretty sharp dude.. and don't you ferget it young fella

Rudi sure gotr that right.

Bill

Rudi and Bill thank you for your kind words. It means a lot to me.

Billy

Billy,
I'm not in a hurry to get the spacer. Thanks for finding the right pipe size to make it. I can't find anything in my pile of scrap stuff that will work.
I read about the Lister and it will be to see it in operation at Cubfest. Look foward to seeing you again.

Thanks
Ron