Page 1 of 1

Planting sweet corn.

Posted: Thu May 17, 2007 3:08 pm
by Dave F.
Getting ready to plant sweet corn. Saturday, question is how far apart should my rows be, I like to be able to cultivate with the cub. I have the front end & rear tires in the narrowest posistions Thanks Dave F.

Posted: Thu May 17, 2007 3:28 pm
by Bigdog
Dave there was a discussion recently about this. I think the general concensus was 36 to 40 inches works well.

Posted: Thu May 17, 2007 3:28 pm
by Denny Clayton
40" to match your wheel settings.

Posted: Thu May 17, 2007 3:46 pm
by KETCHAM
I went with the std 36" .Kevin :) :) :)

Posted: Thu May 17, 2007 4:12 pm
by pete1941
Dave, that is where mine are set and they work out fine. Pete

Posted: Thu May 17, 2007 8:12 pm
by Boss Hog
Dave, It is easy just follow your tracks when you exit one row come back down with the tires in the outer most track you came out of. what ever the spacing is on your tractor will be yhe same with the cultivatore. That is IF you are using the same tractor to plant as to cultivate with. Believe me an inch or two makes no difference
David

Planting sweet corn

Posted: Fri May 18, 2007 7:44 am
by Dave F.
Dave B. I don't have a planter for my tractor, Planting will be done by hand, so I guess I'll leave 36" to 40" between my rows, Also when I plant my corn seed in the furrows (rows) should I scatter some fertilizer in there also ? Thanks Dave F.

Posted: Fri May 18, 2007 7:50 am
by Rudi
Dave:

We plant the same way. No planter, planting is done by hand be it for corn, taters, beans whatever......

After it is all plowed, disced and level, I start the 1st row with 1/2 of me Cub on the lawn, run down the field, then come back up with my left front tire in the tracks of the first trip. Then I go down with the right front in the preceeding track and keep repeating until I am done.

Then we usually walk the row. We sprinkle a little of 6-12-12 in the tire tracks, then we put down the seed. We then take the hillers and hill up and over. After that it is cultivating time. Probably about 3 weeks after, I manuall side dress with another layer of 6-12-12 and then continue cultivating. Been working for me for about 5 years now since I got Ellie, and about 16 before that working with the Putt-Putt. My father-in-law has been planting like this for nigh on 70 years now. Pretty common for small gardens around these parts.

Hope that was clearer than mud.. :wink: :D There are probably many different methods as there are gardens. :roll: 8) :!:

Posted: Fri May 18, 2007 8:07 am
by pete1941
Rudi,

I know that most of us do with what we have to do with. However, I would strongly suggest you folks look into the planter and fertilize distributor along with the lay off plow and the deep fertilize applicator. Without these, you all are missing out on one of the true joys of gardening with a Cub. You do it all in one pass, lay off the row, apply the seed, put down the fertilize and WALLA, you're finished.

I know that good operational planters, fertilize distributors, etc., are hard to come by, good ones at least, but these put the fun back into gardening!

Pete

Posted: Fri May 18, 2007 1:02 pm
by Rudi
Pete:

I have never seen one.. and most folks I know who have Cubs and have had them for years and sometimes generations ... have never seen them either. They are a very rare critter here on the east coast, and I imagine that they would cost probably significantly more than the prices commanded for them in the US.

Unfortunately, we will probably never get to experience that ...

Posted: Fri May 18, 2007 2:31 pm
by pete1941
Rudi,

Good to hear from you again. For anyone that's looking for planter equipment and the likes, an excellent place to search is what we have here in Georgia, { Farmers and Consumers Market Bulletin}. Most of the southern states have them or at least I know for a fact that Ga, Ala, and Mississippi have them. Our's here in Ga is viewable from a website:

http://.www.agr.georgia.gov

Prices in this area can run for $300. to $600. depending on the quality and completeness of the system. It's awful hard to find plates, gears, etc. but they can be found. I have several extra plates for the duplex hopper as well as gears for this. With as many talented folks that I have seen on the Forum, making plates for the POAX hopper that was discussed a few days ago, would be a breeze, especially those of you with machine shops and the know how.

Everyone should have the opportunity, at least just for once, to operate the Cub with this attachment. It is truly a joy!!!! Right now I have the plows on my Cub, but plan to put the planter back on next week. When I do, I'll get pictures and if I can figure out this posting to the forum deal, I'll put them there for everyone who hasn't seen one, to see. Might have to have your assistance, but I know that won't be a problem. Regards, Pete

Posted: Sat May 19, 2007 8:29 am
by KETCHAM
Next year I'll have my planter going!!!Doing by hand is a lot of work.I did that the last two years with Tracy.This year I bought a little 2 wheeled planter and the thing work great!!kind of pricey at $60.00 but cut planting time down to a couple of hours!!!I have 1 seed plate now for my cub [small sweet corn] and hope to get beans and peas for next year.I'm luckey to have traded for my planter.[Traded a frt blade for it]Kevin