154 loboy clutch brake question

IH CUB LoBoy Series - 154, 184, 185 Forum -- Questions and answers to all of your LoBoy related issues.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.

154 loboy clutch brake question

Postby JGtools » Tue Feb 16, 2010 7:27 pm

How do I know if I need to replace the clutch brakes? ( 2- round plastic like brakes) they install in the retainer that bolts to the trans case. I assume the brakes wear, and need replacing/ One side of the brakes appear flat, and has a wood like grain sticker on it>>? also is there a right and wrong way to insert the brakes into the retainer? thanks for the help Jim
JGtools
501 Club
501 Club
 
Posts: 934
Joined: Tue Dec 18, 2007 8:18 pm
Location: Dassel, Minnesota
Zip Code: 55325
Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy

Re: 154 loboy clutch brake question

Postby Bermuda Ken » Wed Feb 17, 2010 4:49 pm

These (404642R1) should look like a pool cue stick tip. The "woodgrain tip" should face/contact the steel flywheel.
Cub Cadets....Engineered for people who know better!
User avatar
Bermuda Ken
501 Club
501 Club
 
Posts: 632
Joined: Fri Feb 07, 2003 8:43 am
Location: Wisconsin The Badger State
Zip Code: 53521
Tractors Owned: Tractors owned past/present:

Farmall.....F-1206, F-806 sn#501.

Cub Cadet...Original(s), 122, Spirit of 76, 1200, 1250, 1450, 782, 782 Diesel (2), 984, 982 CADET 000 LT Prototype.
Circle of Safety Award
Circle of Safety: Y

Re: 154 loboy clutch brake question

Postby JGtools » Thu Feb 18, 2010 7:21 am

Ken, that would be the flat side makes contact with flywheel. The rounded part faces retainer. thanks,Jim
JGtools
501 Club
501 Club
 
Posts: 934
Joined: Tue Dec 18, 2007 8:18 pm
Location: Dassel, Minnesota
Zip Code: 55325
Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy

Re: 154 loboy clutch brake question

Postby Dave Hull » Sun Feb 21, 2010 8:07 pm

Usually the way to tell if you have a problem is the clutch brake doesn't stop the clutch and you "grind them till you find them". The usuall problem is too much wear in the linkage system, causing continual adjustment. Tighten up the linkage with new bushings(welded in) and the adjustment will be few again.
Dave Hull
Cub Star!
Cub Star!
 
Posts: 226
Joined: Sun Jul 20, 2003 6:16 pm
Location: Cookeville, TN
Zip Code: 38506

Re: 154 loboy clutch brake question

Postby JGtools » Sun Feb 21, 2010 9:32 pm

Dave, do you have any pictures of the linkage fix? Not sure I understand. I know the bolt that connects to the brake bracket, has adjustment ,By turning in or out, not sure what bushings you are talking about, thanks Jim
JGtools
501 Club
501 Club
 
Posts: 934
Joined: Tue Dec 18, 2007 8:18 pm
Location: Dassel, Minnesota
Zip Code: 55325
Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy

Re: 154 loboy clutch brake question

Postby Dave Hull » Sun Feb 21, 2010 10:49 pm

Jim,
Check all the moving joints between the foot pedal back to the point the clutch brake starts to engage. Any wear throughout the system(like the pivot points where pins wear against holes in the brackets), this lash adds up through the linkage and often time is greater than what is available in the adjustment back at the brake. This is why on older units people complain of constantly having to adjust. I have seen some clever adaptations where the brake can be applied by hand directly on the clutch brake itself. These are quite effective, but do require one hand to "hand brake" and use of your other hand to select the next gear.
Dave Hull
Cub Star!
Cub Star!
 
Posts: 226
Joined: Sun Jul 20, 2003 6:16 pm
Location: Cookeville, TN
Zip Code: 38506

Re: 154 loboy clutch brake question

Postby JGtools » Sun Feb 21, 2010 11:02 pm

Thanks Dave. I was wondering why Ih did not have a true brake pad, kind of like the old hand clutch days, and belt pulley brakes, that used a brake lining to stop the pulley? I will check the linkages, and do my best. thanks again, Jim
JGtools
501 Club
501 Club
 
Posts: 934
Joined: Tue Dec 18, 2007 8:18 pm
Location: Dassel, Minnesota
Zip Code: 55325
Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy

Re: 154 loboy clutch brake question

Postby WestDeerPirate » Fri Mar 15, 2013 7:25 pm

Hi, Iknow this is 3 years ago but what worked?
WestDeerPirate
Cub Star
Cub Star
 
Posts: 65
Joined: Sat Jun 05, 2010 7:39 pm
Location: West Deer Township, PA
Zip Code: 15044
Tractors Owned: 1970 International Cub Low Boy 154


Return to LoBoy Series - 154, 184, 185

Who is online

Users browsing this forum: No registered users and 1 guest