184 clutch failed

IH CUB LoBoy Series - 154, 184, 185 Forum -- Questions and answers to all of your LoBoy related issues.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
outdoors4evr
5+ Years
5+ Years
Posts: 987
Joined: Tue Jul 22, 2008 12:44 pm
Zip Code: 48423
Tractors Owned: 184
Location: Davison, MI

184 clutch failed

Postby outdoors4evr » Fri Aug 12, 2011 6:48 pm

One year and four months after replacing the clutch, pressure plate, throwout assembly, pilot bearing, driveshaft, and u-joint the clutch has failed.

I probably have less than 100 hours on it with zero hours of pulling. Just driving (mowing and snow thrower work).
The clutch disc itself still looks new, but the hub separated from the clutch. All of the rivets were broken off and the tops of the rivets were laying in the flywheel. The rivet holes look like they are oblong rather than circular so it probably was not tightly riveted to begin with.

Tomorrow I will go back to the Case IH Dealer the part was purchased from and see what they say. I bought the parts originally from a dealer to avoid poorly made foreign parts. The original part lasted 30 years and I had hoped using OEM parts that I would get similar results. I hope they didn't just sell me a cheap part and charge me dealer prices. I really don't want to replace a clutch component every year and a half.

Anyone else have a similar issue with poorly riveted clutches?
Should I tag weld the hub or would that just warp it?
Should I just try another and hope it isn't defective?
184 w/ Creeper & 3-Point
IH 3160a Mower
IH Model 15 Tiller

User avatar
Bigdog
Cub Pro
Cub Pro
Posts: 24066
Joined: Sun Feb 02, 2003 12:50 pm
Zip Code: 43113
Circle of Safety: Y
Location: OH, Circleville

Re: 184 clutch failed

Postby Bigdog » Sat Aug 13, 2011 8:34 am

I find a lot of dealer parts aren't what they used to be. Some dealers are even stocking aftermarket parts for re-sale. If you go to my local dealer and ask for a cub carb kit you will get a Tisco kit.
I suspect the clutch you got was a similar situation. Most likely from south of the border or overseas. Parts quality just isn't what it used to be. I'd sure let them know I was unhappy. It might not do any good but eventually I hope they get the message before it's too late to find anything still made well.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.

My wife says I don't listen to her. - - - - - - - - Or something like that!

Image

http://www.cubtug.com

outdoors4evr
5+ Years
5+ Years
Posts: 987
Joined: Tue Jul 22, 2008 12:44 pm
Zip Code: 48423
Tractors Owned: 184
Location: Davison, MI

Re: 184 clutch failed

Postby outdoors4evr » Sun Aug 14, 2011 12:00 pm

The part that failed came in "OEM packaging". I suspect it just wasn't riveted correctly.
Hopefully the next OEM Packaged clutch won't have the same issue. I didn't spend the extra dough for the OEM packaging just to have it last a year and a few months. I don't want to do this job again.
184 w/ Creeper & 3-Point
IH 3160a Mower
IH Model 15 Tiller


Return to “LoBoy Series - 154, 184, 185”

Who is online

Users browsing this forum: No registered users and 1 guest