Page 1 of 3
154 Project (photo heavy!!)
Posted: Fri Feb 10, 2012 1:57 am
by RaymondDurban
The tear down is already well under way....
Shipping crate....
Parts cleaned and primed.....
.....more parts cleaned and primed....
Parts ready for primer....
Ready for engine teardown.....
I believe #4 exhaust valve is getting hot....
Not too nasty in there....
Still not too bad.....
Pulling the valves....
Works slick....
Ok, this is nasty....
Valves, tappets and pistons removed and organized... Standard bore and standard bearings....
At least there is no sludge built up on the crankcase walls....
Parts to be cleaned bin is filling up....
Done for the night....
Re: 154 Project (photo heavy!!)
Posted: Fri Feb 10, 2012 2:02 am
by Former Member
Cool Raymond. See you in a week or so
Re: 154 Project (photo heavy!!)
Posted: Fri Feb 10, 2012 5:51 am
by phildidit
lookin good raymond, someone is gonna get a NICE loboy when you are done!!!!!!
Re: 154 Project (photo heavy!!)
Posted: Fri Feb 10, 2012 9:09 am
by twotone
Raymond, you and I are at about the same place on our 154 restorations. I am running out of room though, I need to get the frame sand blasted so I can start assembly and make some room. I noticed that your #4 cyl seems to be the best, so was mine.
I brought a bunch of stuff home from the sandblaster but my son said he would do the frame and front axle, soon I hope. I'm not trying to hijack your thread, just filling it with more 154 pics.
Tom
Re: 154 Project (photo heavy!!)
Posted: Fri Feb 10, 2012 10:43 pm
by RaymondDurban
Re: 154 Project (photo heavy!!)
Posted: Fri Feb 17, 2012 7:28 pm
by dennisbushnell
Who is the mystery man in the first pick? lol
Re: 154 Project (photo heavy!!)
Posted: Fri Feb 17, 2012 9:28 pm
by dirtyred
dale shaw's lil brother?
Re: 154 Project (photo heavy!!)
Posted: Tue Feb 28, 2012 2:45 pm
by twotone
Raymond, I haven't seen any pics of yours lately. I just went through your pics again and you are going way beyond what I'm doing. Yours may take longer, but it will look a thousand times better that mine. Good patience on your part.
Tom
Re: 154 Project (photo heavy!!)
Posted: Tue Feb 28, 2012 4:52 pm
by RaymondDurban
Tom,
I've got more parts cleaned and primed, but no yellow paint yet. You will definitely finish before me, but my goal was to have it done by this summer so that I can help cut some hay for the farmer to the north!
I should make it well before then (I hope!!).
I've got to get my frame, axle and a few other parts and pieces to the sandblaster, then I can start putting things together. The big issue for me right now is the steering wheel. Its in good shape, but frozen solid and while trying to remove it with a puller, I mushroomed the end of the shaft. I'm gonna end up having to cut it off I'm afraid and just buy another one. Hopefully I can save the shaft and not have to replace it too!
Also have to get my order in to HamiltonBob, just been holding out to make sure that I can get all I need in one shipment. Thinking seriously about upgrading to dual brakes as well while I've got it all torn apart.
Re: 154 Project (photo heavy!!)
Posted: Wed Feb 29, 2012 8:32 am
by outdoors4evr
The dual brakes are not real handy when you have a heavy load out front. (like a blade or a blower)
They do work very well if you have a load on the 3-point hitch and can get the balance of the tractor more on the back tires.
Re: 154 Project (photo heavy!!)
Posted: Sun Mar 04, 2012 1:52 pm
by BigBill
I find the dual brakes very handy when one wheel loses traction I can put the power to the wheel that has traction. After seeing how good my 3rd 154 was withy dual brakes i purchased two sets of dual brakes for my other two 154's.
Ray/guys graet job onyour 154's. If your going to restore it do it right.
Ray i know just by looking at your valves there not all carboned up like the ones on my 2nd int154 are. (fel/loader project) The zenith carb that was on it was all beat up by the PO trying to stop it from leaking. My carb looks like someone too a prick punch to the outside rather than pull the bowel to fix the float height or change out the needle and seat. Again laziness on the PO. The carbon is caked up in the ports there almost closed up in the valve area. Bill
One thing to check even though it may look ok is the pullies on the drive shaft and Pto shaft. I've seen these fret on the shaft sometimes. I closer inspection and maybe a tightening up will make sure its ok.
If you look at the front axle bracket area and the vertical plate above it its only welded on one side and the top vertical plate isn't welded to the front axle bracket. Even the welds on one side of the vertical plate are missing on the frame rails. I just tac'd it on both sides and connected everything in that area plus i boxed the very front of the frame rail openings with 3/16 plate too. My pics are in the photo section.
I'm sorry i'm slow with mine do to other things needing attention and my health and the weather holds me up on my restorations.
I purchased almost another 4th int154 in parts on shelves to have the parts on hand inhouse since i have 3 int154's.
1st int154; has 60'' 3260 mower deck w/3pt hitch I'm adding dual brakes. I may add a creeper too for a rear tiller on the 3pt.
2nd int154; has the creeper, fel & backhoe when its done. The farme will be boxed front to rear with 3/16', 1/4'' and 3/8'' + 1/2'' plate in some spots. Power steering and a second hydraulic system. It will have a gearded starter and a 105amp 10si alternator. A six blade fan and maybe an electric fan on the radiator.
3rd int154; Has a creeper tranny, dual brakes an IH snowplow Needs a new clutch and drive shaft.
This is my plan right now.
Re: 154 Project (photo heavy!!)
Posted: Sun Mar 04, 2012 2:15 pm
by BigBill
RaymondDurban wrote:Tom,
I've got more parts cleaned and primed, but no yellow paint yet. You will definitely finish before me, but my goal was to have it done by this summer so that I can help cut some hay for the farmer to the north!
I should make it well before then (I hope!!).
I've got to get my frame, axle and a few other parts and pieces to the sandblaster, then I can start putting things together. The big issue for me right now is the steering wheel. Its in good shape, but frozen solid and while trying to remove it with a puller, I mushroomed the end of the shaft. I'm gonna end up having to cut it off I'm afraid and just buy another one. Hopefully I can save the shaft and not have to replace it too!
Also have to get my order in to HamiltonBob, just been holding out to make sure that I can get all I need in one shipment. Thinking seriously about upgrading to dual brakes as well while I've got it all torn apart.
On my 1st int154 i drilled and tapped two 1/4-20 threaded holes in the steering wheel so the orginal steering wheel puller could be used. Then it came off easily.
I have one steering box were the PO welded a hex nut in the hole in the steering shaft that holds the steering wheel on when the nut area probably broke off. Now the steering wheel is held on with a hex bolt and a larger concaved washer from a shock.
Re: 154 Project (photo heavy!!)
Posted: Wed Mar 14, 2012 7:38 pm
by RaymondDurban
Me and Bob got a bit done on the 154 today. Got everything striped down to the bare frame. Had to cut the steering wheel off and boogered up the end of the shaft just a bit, but it's salvageable. Got the frame, axle, hood and a few other parts dropped off at the sandblaster today, so maybe by the end of next week I can start putting stuff back together.
Re: 154 Project (photo heavy!!)
Posted: Thu Mar 15, 2012 11:35 am
by twotone
I had to take my steering wheel off yesterday to get under the dash to chase some wires. Turns out it was a bad starter. It won't turn over an engine with compression. I probably hate removing the steering wheel worse than anything on these 154's. Note to self: have some behind to catch you when you pull it off with no puller by jerking real hard by hand. First time it EVER came off without a puller.
Tom
Re: 154 Project (photo heavy!!)
Posted: Thu Mar 15, 2012 1:22 pm
by Jim Becker
twotone wrote:Note to self: have some behind to catch you when you pull it off with no puller by jerking real hard by hand.
Loosen the nut but leave it on, so the wheel will stop when it hits the nut.