Hello, I have to change my front oil seal. I need some advice on pulling the crank shaft pulley. I see there is also a bushing in there . Should this be replaced as well.
Thank you, Dave
Oil Seal
Moderator: Team Cub
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
7 posts
• Page 1 of 1
Oil Seal
by Dave Irish » Mon Dec 29, 2003 1:04 pm
- Dave Irish
- 10+ Years
- Posts: 141
- Joined: Fri Feb 21, 2003 12:06 pm
- Location: St. Catharines, ON. Canada
by Jim Hudson » Mon Dec 29, 2003 2:02 pm
I think the bushing (sleeve) will come with the seal if you get it from a case IH dealer. Most come off hard. Don't pull from the edge of pully or it will break the pully. A bearing seperator from a cheap tool supply place like Harbor Freight will work good. Soak with your favorite penetrating oil and it may come off but if it don't leave it alone awhile and tighten more. If all fails you will need some heat. I cannot get anything to come up in the archives on this board but there are lots of post on the other Cub board. http://www.atis.net/cgi-bin/FarmallCub.pl Do a search there.
Young man for work, old man for advice
-
Jim Hudson - 10+ Years
- Posts: 1223
- Joined: Sun Feb 02, 2003 1:11 pm
- Location: Albemarle, North Carolina 28001
- Zip Code: 28001
by artc » Mon Dec 29, 2003 4:38 pm
something i copied a while back from Tim in CA. has a JC Whitney puller #81UJ2372T... 39.99. http://www.jcw.com.
looks like i'm needing one for the '48 cub. it's starting to drip like an old faucet.....so's the radiator
looks like i'm needing one for the '48 cub. it's starting to drip like an old faucet.....so's the radiator
'If they're tappin', they're not burnin'
http://www.ZagrayFarmMuseum.org
http://www.ZagrayFarmMuseum.org
-
artc - Cub Pro
- Posts: 1749
- Joined: Sun Mar 30, 2003 10:25 am
- Location: CT, Middletown
- Zip Code: 06457
- eBay ID: cmtelephone
- Tractors Owned: 1950 cubs (3), 1948 cub, 1941 A, 1948 H, 1963 B414, 1958 240U, 1947 Oliver 60 industrial, Oliver 70 industrial.1948 super AI (trailer queen), 1958 450.
by artc » Mon Dec 29, 2003 4:45 pm
looks good, but i don't see a 1/2 13 bolt option?
http://www.jcw.com/webapp/wcs/stores/se ... 01&Ntk=All
http://www.jcw.com/webapp/wcs/stores/se ... 01&Ntk=All
'If they're tappin', they're not burnin'
http://www.ZagrayFarmMuseum.org
http://www.ZagrayFarmMuseum.org
-
artc - Cub Pro
- Posts: 1749
- Joined: Sun Mar 30, 2003 10:25 am
- Location: CT, Middletown
- Zip Code: 06457
- eBay ID: cmtelephone
- Tractors Owned: 1950 cubs (3), 1948 cub, 1941 A, 1948 H, 1963 B414, 1958 240U, 1947 Oliver 60 industrial, Oliver 70 industrial.1948 super AI (trailer queen), 1958 450.
by Bigdog » Mon Dec 29, 2003 5:07 pm
Art, take a short 1/2-13 bolt and drill a divot in the head. Thread it into the shaft and use the puller against it.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
Bigdog - Team Cub
- Posts: 23820
- Joined: Sun Feb 02, 2003 12:50 pm
- Location: OH, Stoutsville
- Zip Code: 43154
- Circle of Safety: Y
by Jim Hudson » Mon Dec 29, 2003 5:45 pm
I cannot tell if that JC Whitney job is big enough are not.
.jpg)
Young man for work, old man for advice
-
Jim Hudson - 10+ Years
- Posts: 1223
- Joined: Sun Feb 02, 2003 1:11 pm
- Location: Albemarle, North Carolina 28001
- Zip Code: 28001
- Dave Irish
- 10+ Years
- Posts: 141
- Joined: Fri Feb 21, 2003 12:06 pm
- Location: St. Catharines, ON. Canada
7 posts
• Page 1 of 1
Who is online
Users browsing this forum: BIGHOSS, CUBWH, Mike in Louisiana, RaymondDurban, Trent M and 8 guests
|
|