Hello, I have to change my front oil seal. I need some advice on pulling the crank shaft pulley. I see there is also a bushing in there . Should this be replaced as well.
Thank you, Dave
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Oil Seal
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 164
- Joined: Fri Feb 21, 2003 12:06 pm
- Location: St. Catharines, ON. Canada
- Contact:
- Jim Hudson
- 10+ Years
- Posts: 1224
- Joined: Sun Feb 02, 2003 1:11 pm
- Zip Code: 28001
- Location: Albemarle, North Carolina 28001
I think the bushing (sleeve) will come with the seal if you get it from a case IH dealer. Most come off hard. Don't pull from the edge of pully or it will break the pully. A bearing seperator from a cheap tool supply place like Harbor Freight will work good. Soak with your favorite penetrating oil and it may come off but if it don't leave it alone awhile and tighten more. If all fails you will need some heat. I cannot get anything to come up in the archives on this board but there are lots of post on the other Cub board. http://www.atis.net/cgi-bin/FarmallCub.pl Do a search there.
Young man for work, old man for advice
- artc
- Cub Pro
- Posts: 1871
- Joined: Sun Mar 30, 2003 10:25 am
- Zip Code: 06457
- eBay ID: cmtelephone
- Tractors Owned: Restored: 1950 Cub, 1950 Cub Demo, 1948 super AI, 1935 Silver King, 1946 Oliver 60 RC, John Deere M, 1950 C demo.
In working clothes:
1950 cub, 1948 cub, 1941 A, 1948 H, 1963 B414, 1958 240U, 1947 Oliver 60 industrial, Oliver 70 industrial. IH 450, 1963, another 1948 cub, 1946 I6 with Trogan front blade. - Location: CT, Middletown
- Contact:
something i copied a while back from Tim in CA. has a JC Whitney puller #81UJ2372T... 39.99. http://www.jcw.com.
looks like i'm needing one for the '48 cub. it's starting to drip like an old faucet.....so's the radiator
looks like i'm needing one for the '48 cub. it's starting to drip like an old faucet.....so's the radiator
'If they're tappin', they're not burnin'
http://www.ZagrayFarmMuseum.org
http://www.ZagrayFarmMuseum.org
- artc
- Cub Pro
- Posts: 1871
- Joined: Sun Mar 30, 2003 10:25 am
- Zip Code: 06457
- eBay ID: cmtelephone
- Tractors Owned: Restored: 1950 Cub, 1950 Cub Demo, 1948 super AI, 1935 Silver King, 1946 Oliver 60 RC, John Deere M, 1950 C demo.
In working clothes:
1950 cub, 1948 cub, 1941 A, 1948 H, 1963 B414, 1958 240U, 1947 Oliver 60 industrial, Oliver 70 industrial. IH 450, 1963, another 1948 cub, 1946 I6 with Trogan front blade. - Location: CT, Middletown
- Contact:
looks good, but i don't see a 1/2 13 bolt option?
http://www.jcw.com/webapp/wcs/stores/se ... 01&Ntk=All
http://www.jcw.com/webapp/wcs/stores/se ... 01&Ntk=All
'If they're tappin', they're not burnin'
http://www.ZagrayFarmMuseum.org
http://www.ZagrayFarmMuseum.org
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
Art, take a short 1/2-13 bolt and drill a divot in the head. Thread it into the shaft and use the puller against it.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
- Jim Hudson
- 10+ Years
- Posts: 1224
- Joined: Sun Feb 02, 2003 1:11 pm
- Zip Code: 28001
- Location: Albemarle, North Carolina 28001
-
- 10+ Years
- Posts: 164
- Joined: Fri Feb 21, 2003 12:06 pm
- Location: St. Catharines, ON. Canada
- Contact:
Who is online
Users browsing this forum: Bill V in Md, DBIZZELL, jobbyjim, Mike in Louisiana and 41 guests