Farmall Cub Forum -- Questions and answers to all of your Cub related issues.
Moderator: Team Cub
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
9 posts • Page 1 of 1
Took my two year old restoration out yesterday for a run to keep all the crannies oiled and the bearings lubed up. Noticed two things
1. The IH paint 2150 I used for the restoration had turned orange in the area of a gas spill and where the radiator overflow had spit. Around the top of the gas tank had turned orange. I am very dissapointed for choosing the 2150 now. I have used PPG Omni on other equipment and it held up much much better. I am pretty sure I put it on correctly, and it is pretty when new, but I would not recommend it long term.
2. During my restoration I replaced all the seals in the area of the distributor and none of the shafts had seal wear. Yesterday I drained a couple of ounces of oil out of the distributor body! Cleaned it up well and cleaned the points and rotor up. If anyone has experienced oil in the distributor I would appreciate any insight.
I do love my little Cub and think it is the neatest little tractor. I am currently restoring an 8N Ford and it too is a well designed and fun to drive tractor. I do enjoy reading this board daily.
Not much of a painter myself, but I have seen some posts to the affect that using a hardner in the IH2150 helps prevent the discoloration from gas spills.
Also, did you replace the oring in the end of the distributor?
"The Constitution is not an instrument for the government
to restrain the people, it is an instrument for the people to restrain the
government lest it come to dominate our lives and interests." Patrick Henry
There is a seal on the distributor shaft itself. It is an o-ring in a brass "donut". Did you change this o-ring? I think you have to remove the gear from the end of the shaft and pull the shaft up through the distributor top. You also have to remove the clips that hold the distributor and seperate the "top" housing from the "bottom" half. Do you have a parts book to look at? Just a guess as I almost missed it on mine.
The four most expensive words in tractor restoration: "We might as well..."
I don't have any insight just wanted to say I too have experienced oil in the distributor and have cleaned it out from time to time. You know how these things go I'm puttin up with it for now.
"On your Paint problem it's not uncommon weather using Omnie, Dupont or any other brand, If you don't use Hardner, You have lost the battle."
I did use hardner, however I couldn't find anyone who could help me with the ratio and I might have gone low. On the Omni paint I always use hardner and reducer as per the instructions and it really turns out nice. I think there are even much more expensive paints out there but I would need an antacid if I paid that much. I do a lot of things twice anyway. I tell people that I have a minor in Calculus because I had to take it so many times to pass it.
I have been told by automotive painters that if you take your can of CaseIH 2150- Rouge Red into a quality auto paint supplier, that they can determine the "correct recipe" for that product.
When I was in school I struggled with calculus. And as an aspiring EE I needed to do well so I had a friend help me. His comment to me was "the hardest part about this is copying it over to hand in." This guy was very smart and helped me greatly but put a screw driver in his had and if he didn't kill himself he would kill the closest thing to him. Some times it's OK to do things twice. After all that's the best way to learn.
Maybe this is the first time I didn't run with the crowd... I have a test that argues against using hardener. I have two Cubs painted within two weeks of each other. One with hardener in the 2150 and the other one without. The hardener made the job a little easier, but it added NOTHING to the finished job. The one with hardener will have to have the tank repainted, while the one without hardener is fine. Neither has had any fuel spilled on it, but the fumes escaping from the cap have attacked the primer and caused the topcoat to wrinkle.
Health considerations are another BIG reason to NOT use hardener. I'm sure the hardeners caused much of my chronic lung disease. Because of the disease, I haven't painted anything in four years. A word to the wise!
The most affectionate creature in the world is a wet dog. Ambrose Bierce
9 posts • Page 1 of 1
Who is online