This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Tire wobbles
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 694
- Joined: Tue Feb 04, 2003 6:17 am
- Location: NH, Ossipee
Tire wobbles
Hi all
I hope everyone is doing wll. The right front tire on my 61 wobbles. The wheel bearings seem okay, and there is not a lot of movement up the top where the key fits into the keyway. The tierods are straight and dont seem to have alot of play. How do I tell what is worn ? I know the toe in is not correct just by looking at the outside edge of the tires. It almost looks like the bottom of the tire is in more than the top, not the toe in but I think you call it the caster or camber. If I raise the front end of the ground and wiggle the tire in all dirrections, how do I know what is worn out? As always THANK YOU !! Paul K. in N.H.
I hope everyone is doing wll. The right front tire on my 61 wobbles. The wheel bearings seem okay, and there is not a lot of movement up the top where the key fits into the keyway. The tierods are straight and dont seem to have alot of play. How do I tell what is worn ? I know the toe in is not correct just by looking at the outside edge of the tires. It almost looks like the bottom of the tire is in more than the top, not the toe in but I think you call it the caster or camber. If I raise the front end of the ground and wiggle the tire in all dirrections, how do I know what is worn out? As always THANK YOU !! Paul K. in N.H.
-
- 10+ Years
- Posts: 167
- Joined: Mon Feb 03, 2003 2:24 pm
- Location: Pima, Az.
Paul, raise the wheel that has the wobble off the ground. I would check first for a bent wheel. Take an object like a milk crate and set it close to the wheel, three or four inches. If you have a large file without a handle, lay it on top of the milk crate and position the handle end close to the tire and rotate the tire while looking for the "wobble" as the tire turns to see how much there is. Place your hands at 180 degrees on the tire and push with one hand while pulling with the other. Is the tire and wheel moving when you do this? If the spindle doesn't move with the wheel and tire, then the wheel bearings are loose or worn out. If the bearings aren't the problem, you probably have a bent wheel. It isn't too hard to find the problem when the tire is off the ground, just move it and look for the excess play. I believe the toe in is 1/4". The spindle bushings could also be worn alowing excess caster and camber, there again, look for excess movement while shaking the wheel.
Michael
Michael
- artc
- Cub Pro
- Posts: 1871
- Joined: Sun Mar 30, 2003 10:25 am
- Zip Code: 06457
- eBay ID: cmtelephone
- Tractors Owned: Restored: 1950 Cub, 1950 Cub Demo, 1948 super AI, 1935 Silver King, 1946 Oliver 60 RC, John Deere M, 1950 C demo.
In working clothes:
1950 cub, 1948 cub, 1941 A, 1948 H, 1963 B414, 1958 240U, 1947 Oliver 60 industrial, Oliver 70 industrial. IH 450, 1963, another 1948 cub, 1946 I6 with Trogan front blade. - Location: CT, Middletown
- Contact:
check this tip on rudi's site on toe in alignment.
http://www.cleancomputes.com/Cub/Mainte ... index.html
http://www.cleancomputes.com/Cub/Mainte ... index.html
'If they're tappin', they're not burnin'
http://www.ZagrayFarmMuseum.org
http://www.ZagrayFarmMuseum.org
-
- 10+ Years
- Posts: 694
- Joined: Tue Feb 04, 2003 6:17 am
- Location: NH, Ossipee
Hi All
I jacked up right front, held tire at top and bottom no movement in and out at all. I grab tire at 3 and 6 oclock position and everything seems tight except all kinds of play in the tie rod, not the tie rod end but in the middle where it hooks up to the steering. I did not take that middle piece apart yet. The grease fitting is snaped off there so the pre. owner didn't grease that spot. Does this mean I need new tie rods ? To bad they are so straight. Is there something else in there that is worn out, a part of the steering ? When I take that apart about what size should the end of the tie rod be ? Jacked up the left side a little play same spot, but I never noticed that wheel wobbling. Well as always THANK YOU !! Paul K. in N.H.
I jacked up right front, held tire at top and bottom no movement in and out at all. I grab tire at 3 and 6 oclock position and everything seems tight except all kinds of play in the tie rod, not the tie rod end but in the middle where it hooks up to the steering. I did not take that middle piece apart yet. The grease fitting is snaped off there so the pre. owner didn't grease that spot. Does this mean I need new tie rods ? To bad they are so straight. Is there something else in there that is worn out, a part of the steering ? When I take that apart about what size should the end of the tie rod be ? Jacked up the left side a little play same spot, but I never noticed that wheel wobbling. Well as always THANK YOU !! Paul K. in N.H.
-
- 10+ Years
- Posts: 167
- Joined: Mon Feb 03, 2003 2:24 pm
- Location: Pima, Az.
If you will remove the small plate where the tie rod ends go to the steering, you should find some shims. They are for adjusting the fit of the ball jont in its socket. The less shims, the tighter the fit. As old as these tractors are, the ball and/or socket may have a lot of wear, especialy if they haven't been greased.
Michael
Michael
-
- 10+ Years
- Posts: 694
- Joined: Tue Feb 04, 2003 6:17 am
- Location: NH, Ossipee
Hi All
I took apart the tie rods to the steering gear arm. I had to use a round wire brush in a drill and a pick to clean out old hardened grease and find the little hole in the arm sockets where the grease enters. Arm sockets don't look to bad, looks like a machine flat of about 9/32 up in the middle of both sockets. The top of the tie rods have flats no very smooth, but not to bad, the flats are about 5/8 , is that about the size they are for the grease to get in there ? I see shims that Michael in Arizona told me about. The grease fitting is broken off and the parts book says in group 5 part # 24 1/4 28 ns taper str lube. My question on that is what is the drill and tap size for that fitting, or is that the tap size for the fitting ? Last thing is with the steering arm gear disconnected from the tie rods, the arm has about an 1/8 free play left to right, is that not to bad for now until one day my nerves will allow me to drop all of it and do some more work on it ? Sorry about the long post , and THANK YOU !! Paul K.in N.H.
I took apart the tie rods to the steering gear arm. I had to use a round wire brush in a drill and a pick to clean out old hardened grease and find the little hole in the arm sockets where the grease enters. Arm sockets don't look to bad, looks like a machine flat of about 9/32 up in the middle of both sockets. The top of the tie rods have flats no very smooth, but not to bad, the flats are about 5/8 , is that about the size they are for the grease to get in there ? I see shims that Michael in Arizona told me about. The grease fitting is broken off and the parts book says in group 5 part # 24 1/4 28 ns taper str lube. My question on that is what is the drill and tap size for that fitting, or is that the tap size for the fitting ? Last thing is with the steering arm gear disconnected from the tie rods, the arm has about an 1/8 free play left to right, is that not to bad for now until one day my nerves will allow me to drop all of it and do some more work on it ? Sorry about the long post , and THANK YOU !! Paul K.in N.H.
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Paul:
I can't help you with most of it, just one item and that is the zerk or grease fitting. On Ellie-Mae it was broken off as well - just the top part. The base was still there and I could get a socket on it. I carefully used the ratchet to remove the zerk - it is the threaded type. They are available at any auto-parts store and are about $1.99 for 2 or 3 in a pack. You can get various styles. Because of the way the bolt is in I had to use a 45 deg zerk, but a regular straight one is what is called for.
Hope that makes a little sense.
I can't help you with most of it, just one item and that is the zerk or grease fitting. On Ellie-Mae it was broken off as well - just the top part. The base was still there and I could get a socket on it. I carefully used the ratchet to remove the zerk - it is the threaded type. They are available at any auto-parts store and are about $1.99 for 2 or 3 in a pack. You can get various styles. Because of the way the bolt is in I had to use a 45 deg zerk, but a regular straight one is what is called for.
Hope that makes a little sense.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 694
- Joined: Tue Feb 04, 2003 6:17 am
- Location: NH, Ossipee
Hi Rudi
The fitting on mine is broke off flush with the top, I don't know what threads are on those fitting. I don't want to drill what is left out with to big of a bit, also it is not a through hole and I dont think it needs to be drilled down very deep at all. I posted all that other info, so the pro's could tell me how bad the rods are worn. THANKS !! Paul K in N.H.
The fitting on mine is broke off flush with the top, I don't know what threads are on those fitting. I don't want to drill what is left out with to big of a bit, also it is not a through hole and I dont think it needs to be drilled down very deep at all. I posted all that other info, so the pro's could tell me how bad the rods are worn. THANKS !! Paul K in N.H.
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
Paul, you might try tightening the nut that holds the steering arm and see if that takes some of the play out of it.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
- 10+ Years
- Posts: 694
- Joined: Tue Feb 04, 2003 6:17 am
- Location: NH, Ossipee
Hi Bd
I may get to try that tomorrow, it don't seem to bad at the arm, but if it can be even better that would be great. I really want to know what size the threads are on the zerk fittings, I guess I could go buy a couple as I need them anyway and ask the folks at the parts store. THANK YOU !! Paul K. in N.H.
I may get to try that tomorrow, it don't seem to bad at the arm, but if it can be even better that would be great. I really want to know what size the threads are on the zerk fittings, I guess I could go buy a couple as I need them anyway and ask the folks at the parts store. THANK YOU !! Paul K. in N.H.
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
From what you posted above, it's 1/4" X 28 threads per inch. A Craftsman screw extractor should take the threaded stub out.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
- 10+ Years
- Posts: 694
- Joined: Tue Feb 04, 2003 6:17 am
- Location: NH, Ossipee
-
- 10+ Years
- Posts: 694
- Joined: Tue Feb 04, 2003 6:17 am
- Location: NH, Ossipee
-
- 10+ Years
- Posts: 167
- Joined: Mon Feb 03, 2003 2:24 pm
- Location: Pima, Az.
Paul, something doesn't sound right to me here. Grease fittings use pipe sizes and 1/4 X 28 is not a pipe size. The 1/4 would be a very large grease fitting and it would not be 28 TPI, but 18. I'm going to guess 1/8 pipe and the TPI would be 27. The tap drill would be a 11/32 drill for the 1/8. It sure would be nice if you could get the broken part out. Any chance you could file or grind a flat on the broken fitting and then weld a nut to it? Allow it to cool and then turn it out. Another method I don't like as well as the welding a nut to it is to take a small torax bit, like a #15 or 20, drill the center of the broken fitting to the same size as the center of the torax then drive the torax bit into the broken fitting. Use a hand impact tool to reverse the fitting out. Lots of soaking with penetrating oil will help.
Michael
Michael
-
- 10+ Years
- Posts: 661
- Joined: Wed Mar 05, 2003 9:09 pm
- Zip Code: 18603
- Tractors Owned: 1948 Cub
1955 Cub - Location: PA, Berwick
- Contact:
Michael Az wrote:Paul, something doesn't sound right to me here. Grease fittings use pipe sizes and 1/4 X 28 is not a pipe size.
Mike. I have used a 1/4-28 NF tap in lieu of 1/8-27 NPT when the pipe tap was not available. The two sizes are very close. This works and seats quite well due to the taper in the male threads. Also, see below paragraph.
Paul. If indeed the size is 1/4-28, then get a 1/4-28 SAE-LT zerk fitting. They are a tapered automotive "Lubricating Thread" series size.......
Ron
Who is online
Users browsing this forum: No registered users and 51 guests