This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Zenith Carburetor
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 86
- Joined: Sun Feb 15, 2004 9:33 am
- Zip Code: 44882
- Tractors Owned: !949 Farmall Cub
- Location: Sycamore, Ohio
Zenith Carburetor
Well guys I got a Zenith carb and the hose to connect it to the breather. Question 1, the hose apparently replaces the metal pipe and I would like to know if I can cut about 2 inches from the pipe and use it as a splice to connect? Question 2, the two linkages are the choke and the govenor, correct? Question 3, Can I take the part from my old carb and place it on the spindle so that both rods are attached on the same side of the carb? Question 4, any recommendations on gasket sealer? I apologize for all the questions, I just do not have much practical experience. Thanks in advance, Bob
Bob Hawley
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Bob:
Here is the blow up of the Zenith Carb:
If I remember correctly from a previous post, there is an adapter hose that fits the air breather on one end and the zenith on the other. Don't cut the breather pipe! Get the adapter hose.... part number 13 on the drawing below with a Case IH part number of 107 142 C1
Hope it helps
Here is the blow up of the Zenith Carb:
If I remember correctly from a previous post, there is an adapter hose that fits the air breather on one end and the zenith on the other. Don't cut the breather pipe! Get the adapter hose.... part number 13 on the drawing below with a Case IH part number of 107 142 C1
Hope it helps
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 86
- Joined: Sun Feb 15, 2004 9:33 am
- Zip Code: 44882
- Tractors Owned: !949 Farmall Cub
- Location: Sycamore, Ohio
Rudi, Thanks for the info. I see the two connectors at either end. I didn't realize there was one at the top. I will have to look up under the hood a little closer. The layout of the carb I also have in your earlier recommendation on the parts book. I will have to study it longer. I don't see it quite the way the picture shows it, but I will get there. Thanks again, Bob
Bob Hawley
-
- 10+ Years
-
- 10+ Years
- Posts: 86
- Joined: Sun Feb 15, 2004 9:33 am
- Zip Code: 44882
- Tractors Owned: !949 Farmall Cub
- Location: Sycamore, Ohio
- George Willer
- Cub Pro
- Posts: 7013
- Joined: Sun Feb 02, 2003 9:36 pm
- Zip Code: 43420
- Circle of Safety: Y
- Location: OHIO, Fremont
- Contact:
johnbron wrote:I think George W. was making the choke rod adapter for the zenith carb swap. He will probably chime in and give you the correct info.
The choke shaft can be turned around and the I.H. lever used on the same shaft on the engine side. Then the choke rod can be hooked up normally. I think you will want the lever pointing straight down when the choke is off.
George Willer
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
-
- 10+ Years
- Posts: 86
- Joined: Sun Feb 15, 2004 9:33 am
- Zip Code: 44882
- Tractors Owned: !949 Farmall Cub
- Location: Sycamore, Ohio
-
- 10+ Years
- Posts: 86
- Joined: Sun Feb 15, 2004 9:33 am
- Zip Code: 44882
- Tractors Owned: !949 Farmall Cub
- Location: Sycamore, Ohio
Hi Guys! I finally got some time to mount the Zenith on my Cub. I didn't realize not everything lines up. My question now is about the fuel line from the sediment bowl to the carb. At the carb end the line will not seat into the elbow and strainer assembly, do I have to have a different fuel pipe or elbow? Thanks, Bob
Bob Hawley
Who is online
Users browsing this forum: Dale Finch and 55 guests