I am going to rebuild my bearing spindles on my c-3 mower and I was hoping to find the bearing numbers for the spindle so I can have them before I tear them down. does anyone have the part numbers?
Chad
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
c-3 mower spindle bearing number
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- cjpenny89
- 10+ Years
- Posts: 1080
- Joined: Mon Feb 03, 2003 1:15 pm
- Location: St. Charles, MI 48655
-
- 10+ Years
- Posts: 121
- Joined: Thu Feb 13, 2003 1:05 am
- Location: Mt. Washington, KY
Chad,
I have a copy of the manual but no part's list.
Probably a call to Case/IH dealer will make a long search and short one.
My local NAPA had most of the common TIMKEN #'s available.
Others will probably know more.
I have a copy of the manual but no part's list.
Probably a call to Case/IH dealer will make a long search and short one.
My local NAPA had most of the common TIMKEN #'s available.
Others will probably know more.
Sam "Preacherman" Fowler
God built us a bridge to heaven with two boards and three nails.
God built us a bridge to heaven with two boards and three nails.
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
Chad, Jim Hudson just mentioned doing this to a C-2 spindle. (ATIS list) He didn't mention any bearing numbers, but they should be readily available at NAPA or similar location.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
- Bermuda Ken
- 10+ Years
- Posts: 682
- Joined: Fri Feb 07, 2003 8:43 am
- Zip Code: 53536
- Tractors Owned: Tractors owned past/present:
Farmall.....F-1206, F-806 sn#501.
Cub Cadet...Original(s), 122, Spirit of 76, 1200, 1250, 1450, 782, 782 Diesel (2), 984, 982, CADET 000 LT Prototype. - Circle of Safety: Y
- Location: Wisconsin.......The Badger State
- Contact:
Here's a quick bearing conversion chart:
IH part # 463911R91..........brg cone..............L44643 Timken
IH part # 572564R1...........brg cup/race...........L44610 Timken
The bearings from IH are reasonably priced and are Genuine Timken brand too.
IH part # 463911R91..........brg cone..............L44643 Timken
IH part # 572564R1...........brg cup/race...........L44610 Timken
The bearings from IH are reasonably priced and are Genuine Timken brand too.
Cub Cadets....Engineered for people who know better!
- Peter S
- 10+ Years
- Posts: 69
- Joined: Fri Jul 18, 2003 11:24 am
- Zip Code: 01085
- Tractors Owned: 1951 cub
1963 cub - Location: Massachusetts
- cjpenny89
- 10+ Years
- Posts: 1080
- Joined: Mon Feb 03, 2003 1:15 pm
- Location: St. Charles, MI 48655
thank you very much guys! that is the same part numbers that my sun master clipper "KUB KLIPPER" 60" mower uses. best thing about that is I can walk into autozone and buy a timken wheel bearing kit for $10 and it has both bearing and cones and the seals are stock items here at work and all I have to do is pay the parts room for them.
thank you again!
Chad Penny
thank you again!
Chad Penny
- cjpenny89
- 10+ Years
- Posts: 1080
- Joined: Mon Feb 03, 2003 1:15 pm
- Location: St. Charles, MI 48655
well its been a while since I bought one 2 summers ago. I went in asked for the same numbers as was said above and the guy looked it up and he walked out to the shevles and he grabbed a bearing kit. It had timken bearings in it. I guess just look by the trailer stuff. I will look today at lunch if I get a chance.
Chad
Chad
Who is online
Users browsing this forum: No registered users and 33 guests