Have a safety tip you want to share? Did you or a friend learn it the hard way? Help someone else by posting your tips on tractor, farm, shop, lawn, garden, kitchen, etc., safety.
Moderator: Team Cub
Safety is an important and often overlooked topic. Make safety a part of your everyday life and let others know how much you care by making their lives safer too. Let the next generation of tractor enthusiasts benefit from your experience, and maybe save a life or appendages.
13 posts • Page 1 of 1
OK, I'll do the first cold post in this forum, and hopefully get this rolling
Keep several pairs of safety glasses/goggles around your shop. Often they get misplaced and rather than take the time to look for them, it is easy to just say to yourself, "I'll just be careful this one time."
If you have several pair place strategically around the shop, there is likely to be a pair within easy reach when you need them -- It's a lot cheaper to buy a few extra pairs of safety glasses, than to lose an eye.
Keep it safe!
PS: More tips on eye safety? Add them here or make a new topic!
I wear glasses - safety glasses all the time. For years I have ordered and obtained prescription lenses and frames meeting the Z87-2 (safety glasses) ANSI standard.
The lenses and frames (for me) have been less expensive than the same frame and lense not meeting the safety standard. By a considerable amount. My current lenses and frames are at least 3 years old. I need new lenses but the frames are still in excellent condition.
I have the feeling that the sales people do not want to sell safety glasses. You need a good excuse to obtain them. I tell the sales people that I'm involved in the maintenance field and that I am required to either have the prescription safety glasses or wear glasses and safety glasses.
I have an excuse. CRS.
Thanks Dennis for the reminder. I learned the hard way. I wear glasses and have since I was ten. One day I was using a brush on my hand grinder to remove rust. Some of the rust got in my eye and embedded in the eye ball. It was so deep that the doctor had to grind part of my eye ball off, that sure makes me remember to use safety glasses. Sure don't want to loose my eye sight.
My wife has a long honey do list, I read it, thank about it, than take a nap to see if it goes away.
seems like it would be a no brainer but oh too often i'll just be careful or its only a tiny bit of weld to grind then whammo
the last piece of metal cost i think $60.00 at the eye doctor to be removed could of bought a whole bunch of pairs
even though i did soon there after
have to think safety otherwise if ya get hurt that's less cub time
Also, remember when wearing a face shield, wear safety glasses too. Face shields are not designed for the same impact resistance as glasses.
Brute force and Ignorance.
http://www.savethecub.com/cubfests/blac ... san_ad.htm
Wow, thanks Carm. That is something I did not realize with face shields. I always figured they were as good or better than safety glasses
This applies to both the garden (reinforced mesh style) and the clear polycarbonate shields used with lathe (wood or metal) or grinder work. Always wear proper eye protection under the shields. The reinforced mesh style will protect from projectiles but will not protect your eyes from smaller particles.
No, don't ask why I know that..
From someone who has had to have a piece of metal drilled out of their eye... wear safety glasses.
I often forget about the face shield when using a wire wheels on my grinder... that is until I have one of those steel wires comes loose and gets stuck in my face.
1951 McCormick Farmall Cub
recently I was using a cup brush on a angle grinder. It threw a wire out and it went through my clothes and stuck in my belly, ouch!
I was reminded to put on glasses when doing any thing that can throw bits out.
grandpops 52 Fcub #151651, 193 plow, 144 cultivators, 174 runner planter, Type C Duplex hopper, 53 Fertilizer Unit, front/mid mount blade, IH but non Cub 4 foot disc, non IH peg tooth harrow, and one of the infamous and much maligned belt pulleys.
Eugene, are the prescription lenses and frames meeting the Z87-2 (safety glasses) ANSI standard heavier?
"The time you spend making sure you are safe is probably the most productive time you can spend!"
No heavier than the standard frames. I get plastic lenses because they are lighter than glass lenses. The glass lenses are noticably heavier, uncomfortably heavier.
The frames looks just like many normal frames. Nothing unusual. The frames are not the thin wirey type, just standard. They do come with plastic snap on wings/side shields. There is a small "8" marked in the upper outside corner - out of vision on the lenses to indicate that they meet the standard. The frames are marked on the inside indicating the standard.
Big difference I notice is the price. Considerably cheaper.
I have an excuse. CRS.
Safety glasses are a must. I didn't know a piece of metal in your eye was such a big deal. According to my eye doctor, if it rusts, it can stain your cornea. this staining cannot be reversed.
Tractors are made to work!
"A Cub will do as much as a team of horses,.. More in hot weather!" - C. W. Spradlin 1909-1994
13 posts • Page 1 of 1
Who is online
Users browsing this forum: No registered users and 2 guests