Farmall Cub Forum -- Questions and answers to all of your Cub related issues.
Moderator: Team Cub
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
my one cub had a brokem grease zerk in the pivot pin and i guess it hasnt seen grease in a million years and is frozen solid.i tried soaking for 2 weeks with penetrating oil then heat then mildly hitting it with punch.nothing helped.i will keep soaking and repeating what i have done unless someone out there has a better idea.i really need to get it free again because i need to get to lower steering oil seal.
Locktite Freeze & Release? what you guys think?
Just call me coconut... Blonde on the inside!
I'd suggest you just stop talking and walk away lest I forget I was raised to be a lady.
was good idea but tried locktite freeze and release and also seafoam deep creep.....
I apologize if this seems too simple, but have you removed the bolts from the clamps? The pin is scalloped out and it will not move if the bolts are there.
Try a chisel and hammer. Wedge the chisel end into the split ring and hammer it a gently to open up the clearance a little. Then drive out the pivot pin using the hammer and a punch.
1948 Cub w/ snowplow
OK, Miss Farmall, I'll take the plunge>
What this: "Saepe creat molles aspera spina rosas"
Louisiana Cub Fest, March 5 & 6, 2010
3 barns full of Cubs of various condition
A zerk? That's a new one on me.
There was one in the wedding ring I gave my (now) ex-wife, bit I didn't know tractors use them.
She liked hers a lot until she went to a jewelry store...
Is that the part of a grease fitting that unscrews?
“If it ain’t broke, I haven’t 'fixed' it yet”
I've always just heard them referred to as a grease fitting.
For some reason, I was picturing a brake bleeder fitting.
Just read a little about Mr. Zerk. Sounds like a neat guy...
“If it ain’t broke, I haven’t 'fixed' it yet”
kinda funny that different folks have different names for things.i never heard of a pitman arm till i got on here .we just called em sickle drivers.some call them shaker rods etc etc.per someones reply i have removed the bolts so that isnt the problem (but was a legit question) and we can rule out the worn lip because i went out to check on that too.this weekend i will try and wedge a chisel in there to widen the gap but the idea scares me somewhat with cast but i will be carefull.i have owned 4 cubs and so far 3 of them have had this grease fitting broken off.this one is the only one that has been frozen so far.i guess in back in the day if u broke off a grease fitting u just didnt worry about greasing that area anymore.thanks for all your help i will keep u informed
bear, you're right about the cast iron. I'd get two sets of wedging devises. If someone tries to actually open the gap to the point that it'll stay opened wider, it probably will crack/snap. All you want to do is lightly flex the opening wider, so you'll leave each wedge in place. You'll know how much soon as the axle pivots easy. Same principal that IH used with squeezing the area tight against the pin. Remember, we're only talking a thousanth or two. If someone reading this tries to spread he ears abunch, they'll be contacting Ralph.
When I told my dad I've been misplacing things and doing stupid stuff----His reply---"It only gets better"
On my Super A, the front end had developed enough wear that the pin could turn in the steering gear housing. Oh yeah, it was that bad. THEN the pin was froze to the axle tube. I used a big punch and a bigger hammer and beat the out of it and it finally came loose.
Then, I replaced the bottom half of the steering gear housing.
White Demo Super A Restoration Updates
Let us pray for farmers and all who prepare the soil for planting, that the seeds they sow may lead to a bountiful harvest.
"Often the prickly thorn produces tender roses"
Just type "translate whatever you want to translate" at Google, and you will get lots of translation sites.
'52 Farmall Cub "Wile E."
'72 Int'l Cub "Bugs Backhoe"
"Men are from Earth; Women are from Earth. Deal with it!" (attributed to George Carlin)
My cub would not take grease from the day I got it even with air powered grease gun. Now it never will
I spent four hours heating and beating it with a 12lb sledge. While it would turn it would not move in or out. There was rust and built up on the on the axle pin and it did not want to come out of the axle but would slide easily through the clamps without spreading them. I started with a hardened M2 drift and shattered it. Then I took a hardened 5/8 bolt ground the head down until it was the just smaller than the axle pin. Even heating the axle red hot it took 20-30 blows to move it a 1/8 inch. My drift slid sideways on one of the blows and broke a ear off of the clamp. Oh well its apart now
Hope you have better luck than I did Bear
Take care of your equipment and it will take care of you. 1964 cub. Farmall 100 and 130.
"Those that say it can’t be done should not interrupt the ones who are doing it.”
Who is online
Users browsing this forum: Brutalfly and 6 guests