This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
oil pan remove
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 16
- Joined: Sun Mar 15, 2009 10:29 pm
- Zip Code: 44026
oil pan remove
It has been a while since my last entry, and my tractor(hobby) has sat ignored since then. Jumping back in I would like to clean the oil pickup area within the oil pan, but am having trouble removing the pan. I have removed the cap screws and can't seem to see if the pan needs to slide forward to remove or is it being stubborn. Don't want to bend anything.
Mario
Mario
-
- 10+ Years
- Posts: 919
- Joined: Sat Jun 18, 2005 9:41 pm
- Zip Code: 61423
- eBay ID: woodpecker56
- Location: IL, Cameron
Re: oil pan remove
Did you remove the flywheel cover and the bolts on the rear of the pan? If so, it comes right off. It is likely that there is sealer holding it up there, pry it loose gently, it will come down.
- Mike in Louisiana
- 10+ Years
- Posts: 7831
- Joined: Tue Feb 15, 2005 10:10 am
- Zip Code: 71023
- Circle of Safety: Y
- Location: LA, Doyline
Re: oil pan remove
Did you take out the three hard ones in the back??
1975 cub (LouAnn) serial # 245946, 1941 John Deere Model H
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
- Dan England
- Cub Pro
- Posts: 3094
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: 71770
- Location: AR, Waldo
Re: oil pan remove
mario: Have you removed each of the three bolts located at the rear margin of the pan? If so, try sliding a thin knife blade between the pan and block. That may break the bond and release the pan. Dan
- Bigdog
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
- Contact:
Re: oil pan remove
As Lil Red said, there are 3 bolts in the rear flange of the oil pan. They can be a bear to get to. Either a wobble socket or universal joint is necessary. I have also had success with a 1/4" drive socket set and long extension. You have to remove the front cover from the bottom of the torque tube to get to those 3 bolts.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
- Dan England
- Cub Pro
- Posts: 3094
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: 71770
- Location: AR, Waldo
Re: oil pan remove
Mike: You must have nimble fingers. Your post wasn't visible when I started but it posted before mine. Dan
-
- 10+ Years
- Posts: 16
- Joined: Sun Mar 15, 2009 10:29 pm
- Zip Code: 44026
Re: oil pan remove
Thanks all. Are the rear bolts close to hidden. I'll go back and do a better eyeball.
- Mike in Louisiana
- 10+ Years
- Posts: 7831
- Joined: Tue Feb 15, 2005 10:10 am
- Zip Code: 71023
- Circle of Safety: Y
- Location: LA, Doyline
Re: oil pan remove
Yes they are kind of hidden.
Dan, That's the way it was with me also, Lil"red beat me to. I was trying to beat the Bigdog. I was going to go back and edit and the other info. As long as the help is given and received that is what counts.
Dan, That's the way it was with me also, Lil"red beat me to. I was trying to beat the Bigdog. I was going to go back and edit and the other info. As long as the help is given and received that is what counts.
1975 cub (LouAnn) serial # 245946, 1941 John Deere Model H
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
- Dan England
- Cub Pro
- Posts: 3094
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: 71770
- Location: AR, Waldo
Re: oil pan remove
mario: They may be difficult to see but are visible if you are in a well lighted area. As BD said, they are often a pain to remove and replace. Dan
-
- 10+ Years
- Posts: 16
- Joined: Sun Mar 15, 2009 10:29 pm
- Zip Code: 44026
Re: oil pan remove
I did successfully,(and quite easily once the fly wheel cover was removed) remove the oil pan. Intake screen was very clean, however sludge was present in pan bottom as well as two half in nuts buried in the sludge. (I know there not supposed to be there.) I will start poking around, but if anyone has any experience with this and can easily pinpoint a source for these two rogue nuts, please inform.
Having fun on my back with bits of debris falling in my eyes,
Mario
Having fun on my back with bits of debris falling in my eyes,
Mario
-
- Team Cub
- Posts: 11859
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: oil pan remove
Mario, If you could post the size of the nuts, or a photo, it might be easier to guess where they are from. There is a good chance that they were accidentally dropped and the PO did not bother to go fishing for them (or take off the oil pan).
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 10+ Years
Re: oil pan remove
Mario, I had no trouble getting those 3 out but getting them back in... That was another story. Good Luck
- brichter
- Cub Pro
- Posts: 1521
- Joined: Sun Jul 11, 2004 2:23 pm
- Zip Code: 32449
- eBay ID: Kinardhippy
- Skype Name: Billy.Ray.Richter
- Circle of Safety: Y
- Location: FL, Kinard
Re: oil pan remove
Well, I had no trouble getting them back in, but I'm not a girl.
If you're gonna dream or steal, do it BIG
The best things in life aren't things.
1951 Cub
1963 Corvair
lots more junk
The best things in life aren't things.
1951 Cub
1963 Corvair
lots more junk
-
- Cub Pro
- Posts: 7508
- Joined: Thu Aug 31, 2006 7:00 pm
- Zip Code: 02769
- Tractors Owned: 6"F" cubs
5 lo-boys
1 154
1 184
1 IH444
1 Oliver OC3 crawler
1 AC D10
1 IH 100 manure spreader
1 IH model B corn grinder
3 power units
cub demonstrator - Circle of Safety: Y
- Location: Ma. Rehoboth
Re: oil pan remove
When ConnectiKIT pulled his pan, he found a nut that turned out to be the nut that holds the TC pump drive gear in place. Ed
-
- 10+ Years
- Posts: 6
- Joined: Mon Jun 22, 2009 8:07 pm
- Zip Code: 24556
- Tractors Owned: 1949Cub
59c2 Wood Mower - Location: Goode, VA
Re: oil pan remove
This past Saturday "Deadfoot" leaked a gallon of oil will mowing for 5 hours. Is there a manual that illustrate the steps to take to remove the pan and replace the gasket so that I can try to slow the leak I see at the rear of the pan? Deadfoot is also leaking oil from the clutch access hole. The property is rolling hills and somewhat rough, making for a bouncy ride at times.
FYI ...Deadfoot gots its name from the numerous flats it received trying to run over heavily spiked thorns. A Bottle of Slime in each tire (tube) has done the trick!
FYI ...Deadfoot gots its name from the numerous flats it received trying to run over heavily spiked thorns. A Bottle of Slime in each tire (tube) has done the trick!
Who is online
Users browsing this forum: Mike in Louisiana and 50 guests