Farmall H sediment bowl

Farmall H, HV & Super H, 1939-1954

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.

Farmall H sediment bowl

Postby Bob McCarty » Sun Nov 22, 2009 10:25 pm

Shackleton's is leaking around the lever and he called me for advice. He said the packing probably needed to be replaced, but he was surprised that after removing the single nut, he couldn't remove the shut off lever. The Cub bowl has two nuts, and I'm wondering if its just corrosion that is binding his up. Any suggestions?

Thanks, Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
Bob McCarty
Team Cub Mentor
Team Cub Mentor
 
Posts: 5644
Joined: Tue May 25, 2004 8:02 pm
Location: CO, Longmont
Zip Code: 80501
Circle of Safety Award
Circle of Safety: Y

Re: Farmall H sediment bowl

Postby Phillip W. Lenke » Mon Nov 23, 2009 6:08 am

Bob
Bob if it turns freely I would remove the nut only re-wind packing around the shut off shaft and replace the nut, if it has the t - handled style you can drive the pin off the shaft mine had a splined drive pin on our M , if it has the brass 90 the nut will slide off then rewind and replace the nut, do not over tighten the packing, just snug enough that there is some drag when you open and close.
If the shaft will not turn freely then he has to get that loosened first. as you well know.
I would check to make sure it is sealing well before you rewind the packing.
Hope this helps
Phil
"Work Hard ,Play Often,Care Always"
Phillip W. Lenke
5+ Years
5+ Years
 
Posts: 1479
Joined: Wed May 25, 2005 1:21 pm
Zip Code: 43449

Re: Farmall H sediment bowl

Postby KETCHAM » Mon Nov 23, 2009 8:50 am

I belive they are still ava at the IH dealer.Not to much $$$ either.I had to go thru 3 sediment bowls yesterday,I ran out of gas on my 47 and the cork gasket dried up.Put gas in and leaked all over.Dropped the glass bowl[oppps].It was a aftermarket sediment set up.Nothing fit so put an IH org back in.What should have only been a gasket turned out to be a pain in the neck.errrrrrr!!!! :lol: :lol: :twisted: :twisted: Kevin
47 CUB[Krusty] 49 CUB[Ollie] 50 H-- PLOWS DISCS MOWERS AND lots more stuff!!Life is to short -Have fun now cause ya ain't gonna be here long!!!!
User avatar
KETCHAM
5+ Years
5+ Years
 
Posts: 5511
Joined: Thu Jul 28, 2005 2:37 pm
Location: Marshallville Ohio
Zip Code: 44645
eBay ID: kevinb2366
Tractors Owned: 47 Cub 48 Cub 50 H

Re: Farmall H sediment bowl

Postby Don McCombs » Mon Nov 23, 2009 9:00 am

61782C91

$37
Don McCombs
MD, Deep Creek Lake

"1950 Something" Farmall Cub
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A
1951 Farmall Super C w/FH
User avatar
Don McCombs
Team Cub Mentor
Team Cub Mentor
 
Posts: 10553
Joined: Mon Feb 03, 2003 6:45 am
Location: MD, Deep Creek Lake
Zip Code: 21550
Tractors Owned: "1950 Something" Farmall Cub
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A
1951 Farmall Super C w/FH
Circle of Safety Award
Circle of Safety: Y

Re: Farmall H sediment bowl

Postby Jim Becker » Mon Nov 23, 2009 9:56 am

The stem should unscrew from the assembly after the packing nut is unscrewed. He should then be able do whatever is required to redo the packing. Reinstall by reversing the removal steps. If it is an original style, there is no packing. It is a backseating valve. A backseating valve needs to be COMPLETELY open to not leak. Maybe his problem is that the threads for the stem are too gunked up for it to open completely and it all needs a good cleaning.

If cleaning/repacking doesn't fix it, get a new assembly.
User avatar
Jim Becker
Team Cub
Team Cub
 
Posts: 11941
Joined: Sun Feb 02, 2003 3:14 pm
Location: MN
Zip Code: 55319
Circle of Safety Award
Circle of Safety: Y


Return to Farmall H & Super H

Who is online

Users browsing this forum: No registered users and 2 guests