Farmall Cub Forum -- Questions and answers to all of your Cub related issues.
Moderator: Team Cub
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
11 posts • Page 1 of 1
I realize that for many of our members this may be a redundant topic, but for the rest of us, helicoils are a rather intimidating process. Just thinking about it can be enough to put one off of the project for a very long time. I know, cause I am one who was very intimidated by the process and had Ellie's final changed at CubFest Northeast NB 2009 rather than helicoil the damaged implement mounting hole. Unfortunately, due to some rather bad luck etc., that final came loose and as indicated in another thread required replacing again. Since I did not have another final that I could utilize except for Ellie's original final, I had no choice but to finally proceed with the helicoil repair. What follows is my attempt at documenting the process in the hopes that it might help others.
One of the things I realized was that the final needed to be supported somewhat securely so that the drilling would not go awry. A 1/2" drill is a pretty powerful unit, and the older ones like the one pictured below have a heck of a lot of torque. Ellie's final is supported on a 20 liter/5 gallon pail.
A 21/32" drill bit is required for the STI tap. The drill bit is marked with a rudimentary depth gauge - a bit of duct tape to indicate the depth of the bolt hole so that the drill does not actually bottom out.
Ensure that the drill bit is perpendicular to the final/bolt hole in at least 2 axis and keep it that way. It may not seem easy, but it really isn't too difficult. A little practice in other materials may help give you confidence. It is important to keep the rpm's of the drill very low. This may include having to trigger the drill often for very short periods of time. This will keep the rpm down as well as counter the tendency of the drill to grab into the cast and possibly cause damage/injury to the casting/your body parts Pay attention to the depth gauge and stop drilling when the duct tape reaches the same level as the implement mounting boss.
Apply some Rapid Tap paste to the STI Tap and carefully insert up to the end of the starter threads keeping the tap perpendicular to the hole in 2 axis. Ensure that you carefully start the new threads.
Stop often and back out the tap cleaning it as you go.
This is about as far as you can go with the tap. After this point you require a bottoming tap. (I made a bottoming tap from this particular STI tap and finished up the threads - see the Grinding A Bottoming Tap thread)
Finish up the threads with the bottoming tap. There will be a fair amount of debris in the casting after creating the threads. The Rapid Tap will trap some of the debris. To get the rest, utilize compressed air (either from your compressor/canned air) and a magnetic pick-up tool.
Thread a helicoil insert onto the installation tool. Apply a locking thread sealant to the outside of the - I used the Loctite 272 brand. Thread the insert into the threaded hole.
Insert carefully - take your time.. it is not a race. The thread locker provides a lot of working time.
Ensure the insert seats fully.
Remove the insertion tool. I did not try to break off the tang as the insert pretty much bottoms out.
Clean the excess and allow to dry. Maximum strength is after a relatively short cure time.
One thing I learned is that there really is nothing to be afraid of in the helicoiling process. Like any skill, if you take your time, proceed methodically, pay attention to the proper steps/setup etc., the end result will be great. I no longer will be reticent about this process. In fact, I ended up spinning another bolt in the same final, so I am going to have to do this again. Only difference is the final will still be on Ellie
Here are the items needed:
Loctite 272 High Temperature, High Strength Red Threadlocker
HeliCoil Thread Insert Kit, 5/8"-11 x .938
hello from the soggy bayous and swamps of "oily" south louisiana. rudi, you did it again, very informative, and something i have been a little reluctant to try. gives me the little push i needed ! and yes, that type of drill is a HOSS. dakcub was right on target. thanks for the extra effort to pass on great experience. coppersmythe ( slippery ) adams...........................
Way to go Rudi! Now you're ready to drill out and helicoil a carb main jet.
"We don't need to think more,
we need to think differently."
Thanks, Rudi, I have one to do, too. Ed
50 ,52,53,56,59 F Cubs, 55,55,57,63,63 fast hitch, 64 lo-boys, 71 154, 184 lo-boy,61 cadet original. IH spreader,IH corn grinder, Oli. OC3 ,AC D10 ,IH 444 , Potato digger, wagner ldr 3 power units.
Good How To. The only thing I would add, is to wear eye protection when blowing out the chips.
MD, Deep Creek Lake
"1950 Something" Farmall Cub
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A
1951 Farmall Super C w/FH
You are perfectly correct. Proper eye wear should be worn at all times. Actually I wear eye protection at all times and I guess I take it for granted that others do as well. Since my cataract surgery, I now wear some very neat amber safety glasses that I picked up a couple months ago. Prior to that, my eyeglasses were safety/chip/scratch resistance as well. One does not want any metal chips in one's eye -- can be very painful over time.
These are similar to the pair I have
AOS Z87 Safety Glasses
Ya did a great job
Take care of your equipment and it will take care of you. 1964 cub. Farmall 100 and 130.
"Those that say it can’t be done should not interrupt the ones who are doing it.”
Not yet. Gotta get a little more practice in and then get the pole barn ready for that kind of work. I want to have a dedicated drill press in the pole barn with a quick set up jig that will have everything ready to pop in the carb and not have to worry about being a tad bit off. But that is the plan - to be able to do my own carbs or any local ones that need it.
Rudi, you made it look easy--so easy that maybe even I can (and need to) do it. Your photos and explanation of the steps were incredibly helpful. Thanks, Jeff
'49 Cub (#77786) "Jessie"
"64 Farmall Cub (#224657) "Alex"
Cub 54 Blade
193 Moldboard plow
Cub L-38 disc harrow
11 posts • Page 1 of 1
Who is online