removal of transmission input shaft 154 lo boy

IH CUB LoBoy Series - 154, 184, 185 Forum -- Questions and answers to all of your LoBoy related issues.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.

removal of transmission input shaft 154 lo boy

Postby JGtools » Thu Mar 10, 2011 5:32 pm

decided to remove the bad input shaft, Clutch and sheet metal was already off . Next I removed top gear shift lever and cover (8) bolts exposing the shifter forks, rods input shaft and gears.see pic 1. Next i removed rear differential cover (9) bolts ,exposing the rear of the input shaft and left and right shifter rods.see. pic 2 Next I removed the 2 shifter fork set screws/bolts, make sure you are in neutral first. see pic 3. Next go to rear access of differential housing, and I used a piece of steel rod I had on hand, used a light hammer to drive forward shifter rods, take your time, and tap the rods out, you will drive rods through front of transmission housing, the frost plugs will drive out as rod is moved forward and out of transmission housing, be careful of shifter forks as rods move through and remove forks once rod is clear. Cover rod bores with your hand or have someone assist you, make sure not to lose the spring or ball that seats inside rod bore, as rod exits bore ,the spring and ball may release with enough pressure to go flying if bore is not covered with hand.see pic 4. Next I removed clutch shaft oil seal, and through rear access of differential housing I used the same rod for for tapping out shifter rods,to tap out input shaft. As input shaft is moved forward, slowly tap until shaft has mostly cleared rear needle bearing , be careful not to damage bearing, remove gears as shaft exits transmission housing. see pic 5 and 6 This was my first time removing a input shaft, and the job did not take long, about a 1hour. I did already have sheet metal and clutch removed, or this would have taken a few hours more. Thanks Hamilton Bob for your guidance.
Attachments
rear differential cover exposing input shaft.jpg
rear cover differential access
DSC01247 (640x480).jpg
exposed input shaft and gears.
rear differential coverpic 4.jpg
rear cover
shifer forks pic 3.jpg
shifter forks
shifter rods pic 2.jpg
shifter rods
pic 1 shifter cover.jpg
gear shift cover removing input shaft out of transmission housing
JGtools
5+ Years
5+ Years
 
Posts: 934
Joined: Tue Dec 18, 2007 8:18 pm
Location: Dassel, Minnesota
Zip Code: 55325
Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy

Re: removal of transmission input shaft 154 lo boy

Postby JGtools » Thu Mar 10, 2011 5:43 pm

location of springs and shifter poppet ball, left and right side shifter rod bores
Attachments
shifter  rod spring and  ball.jpg
you can see the general location to where the spring and poppet ball seats inside rod bores ( Left and right side bores)
JGtools
5+ Years
5+ Years
 
Posts: 934
Joined: Tue Dec 18, 2007 8:18 pm
Location: Dassel, Minnesota
Zip Code: 55325
Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy

Re: removal of transmission input shaft 154 lo boy

Postby Hengy » Thu Mar 10, 2011 5:54 pm

Hey Jim...

You going to try to make it to the Cheesy Fest this year??

Mike in La Crosse, WI
Mike (Happy as a Lark in Allison Park, PA)
Image Image

Check out my Restoration Thread (1955 Cub, Lewis)
User avatar
Hengy
5+ Years
5+ Years
 
Posts: 7106
Joined: Sat Feb 18, 2006 8:12 pm
Location: PA, Allison Park (Am Hengelsberg)
Zip Code: 15101
eBay ID: lacrosseorgans
Skype Name: Mike.Hengelsberg
Tractors Owned: 1949 Cub "Merlin"
1955 Cub "Lewis"
Cub Trailer
A-60 Blade
Cub-22 Mower
193 Plow
Circle of Safety Award
Circle of Safety: Y

Re: removal of transmission input shaft 154 lo boy

Postby JGtools » Thu Mar 10, 2011 6:15 pm

Mike , very possible I can make it this year. hopefully everything works out this year, I need to meet you all and support a great group . will let you know as time gets closer to the date.
JGtools
5+ Years
5+ Years
 
Posts: 934
Joined: Tue Dec 18, 2007 8:18 pm
Location: Dassel, Minnesota
Zip Code: 55325
Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy

Re: removal of transmission input shaft 154 lo boy

Postby b52c130 » Fri Mar 11, 2011 11:12 am

JG,
"Thank You" - VERY MUCH for all the GREAT pictures !!!!

I have been keeping a 'pictionary' of many parts and procedures on the numbered series cubs and this make a very fine addition to the Transmission Maintenance Section.

Thanks again, NJDale
User avatar
b52c130
5+ Years
5+ Years
 
Posts: 188
Joined: Wed Sep 03, 2008 4:35 pm
Location: Randolph, NJ
Zip Code: 07869

Re: removal of transmission input shaft 154 lo boy

Postby JGtools » Fri Mar 11, 2011 1:19 pm

your welcome . I have used pictures that others have posted several times on repairs , and sometimes pictures can make all the difference for a smooth going repair. Jim
JGtools
5+ Years
5+ Years
 
Posts: 934
Joined: Tue Dec 18, 2007 8:18 pm
Location: Dassel, Minnesota
Zip Code: 55325
Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy

Re: removal of transmission input shaft 154 lo boy

Postby tswicegood » Sun Jul 31, 2011 1:24 am

JGTools thank you a thousand times over. Have a 154 and needed to replace a shifter fork and didn't know how to get the rods out! Can't state enough how extremely appreciative I am of your post/pictures.

Had the 1st/R gear push out of the shifter fork, the gear pushed itself though and would no longer go into reverse since it had 1/2" extra play in it.

Image
tswicegood
 
Posts: 1
Joined: Sun Jul 31, 2011 1:12 am
Zip Code: 27107


Return to LoBoy Series - 154, 184, 185

Who is online

Users browsing this forum: No registered users and 3 guests