22 sickle bar Broken

All non-Cub/Cadet/IH/Farmall/Case tractor and machinery discussions.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
oneofthesedays
5+ Years
5+ Years
Posts: 14
Joined: Mon Jun 20, 2011 11:37 pm
Zip Code: 01430
Tractors Owned: Farmall Cub - 1950?
cultivator, planter, 1 bottom plow
Farmall 100 - 1956
2 bottom plow, disc harrow, 22 sickle bar, snow plow
Location: Ashburnham MA

22 sickle bar Broken

Postby oneofthesedays » Thu Sep 01, 2011 9:24 pm

I have a 22 sickle bar and I think i need to do some welding.
IMG_1489.jpg

I believe this plate should be welded to the flywheel shaft tube
IMG_1488.jpg

can any one confirm this?
You do not have the required permissions to view the files attached to this post.

User avatar
elkshead
5+ Years
5+ Years
Cub Star!
Cub Star!
Posts: 246
Joined: Sat Aug 25, 2007 9:26 pm
Zip Code: 98828
eBay ID: elkshead
Tractors Owned: Farmall M 1943 for parts
Farmall M 1944 Restored
Farmall A 1940 Restored
TD 6 1940 w/ Holt Blade
TD 6 1953
1952 Cub Restored
1962 Cub Lowboy
Circle of Safety: Y
Location: Malaga, WA 98828 Chelan County

Re: 22 sickle bar Broken

Postby elkshead » Thu Sep 01, 2011 10:18 pm

Image

If thats the correct end..... the plate is welded to the round cover, not the tube.
I've never used mine, maybe it should be welded? I'll look closer tomorrow.

oneofthesedays
5+ Years
5+ Years
Posts: 14
Joined: Mon Jun 20, 2011 11:37 pm
Zip Code: 01430
Tractors Owned: Farmall Cub - 1950?
cultivator, planter, 1 bottom plow
Farmall 100 - 1956
2 bottom plow, disc harrow, 22 sickle bar, snow plow
Location: Ashburnham MA

Re: 22 sickle bar Broken

Postby oneofthesedays » Thu Sep 01, 2011 10:26 pm

No, it is the other end, the end that the pitman arm attaches to.

Jim Becker
Team Cub
Team Cub
501 Club
501 Club
Posts: 12164
Joined: Sun Feb 02, 2003 2:59 pm
Zip Code: 55319
Circle of Safety: Y
Location: MN

Re: 22 sickle bar Broken

Postby Jim Becker » Fri Sep 02, 2011 11:46 am

Yes, it should be welded. Also, if your coupling bar has the big bend that it appears to have in the first picture, you need to fix that too. Based on what it would take to bend the coupling bar, you should check the cutter bar for bends too.

oneofthesedays
5+ Years
5+ Years
Posts: 14
Joined: Mon Jun 20, 2011 11:37 pm
Zip Code: 01430
Tractors Owned: Farmall Cub - 1950?
cultivator, planter, 1 bottom plow
Farmall 100 - 1956
2 bottom plow, disc harrow, 22 sickle bar, snow plow
Location: Ashburnham MA

Re: 22 sickle bar Broken

Postby oneofthesedays » Fri Sep 02, 2011 2:13 pm

Thanks, I could not tell from the manual, it shows the plate attached in one view and not in another. yes I do plan on fixing the coupling bar too. Dad hit a rock with the mower and said it stopped him dead, you can't tell in the picture of the un-attached plate but that it was bent too. The cutter bar is OK, he hit right in the center of the tractor. I have all the new teeth, rivots and wear plates just need to find some of that International Blue paint. anyone have on online source, or know where i can find it here in Taxachusetts

Jim Becker
Team Cub
Team Cub
501 Club
501 Club
Posts: 12164
Joined: Sun Feb 02, 2003 2:59 pm
Zip Code: 55319
Circle of Safety: Y
Location: MN

Re: 22 sickle bar Broken

Postby Jim Becker » Fri Sep 02, 2011 3:06 pm

I've used Van Sickle 460 International Blue and been happy with it. You can get it from Ken Updike at Carter & Gruenewald.
http://www.cngco.com/
Kenneth Updike Parts /Internet/ Toy Sales 608.455.2411 Brooklyn kenu@cngco.com

Here is a recent thread on paint:
http://www.farmallcub.com/phpBB2/viewtopic.php?f=1&t=64132

oneofthesedays
5+ Years
5+ Years
Posts: 14
Joined: Mon Jun 20, 2011 11:37 pm
Zip Code: 01430
Tractors Owned: Farmall Cub - 1950?
cultivator, planter, 1 bottom plow
Farmall 100 - 1956
2 bottom plow, disc harrow, 22 sickle bar, snow plow
Location: Ashburnham MA

Re: 22 sickle bar Broken

Postby oneofthesedays » Fri Sep 02, 2011 4:10 pm

Thanks Jim, Paint is on the way, I will post some more pictures as I progress on this restore/repair...

User avatar
BIGHOSS
10+ Years
10+ Years
501 Club
501 Club
Posts: 1542
Joined: Tue Jul 18, 2006 9:55 pm
Zip Code: 37087
Tractors Owned: 1947 Cub S/N 9216
w/ C-22 Mower

1974 Cub S/N 244814
w/59 Woods Mower

Ford 3000 Gas S/N C375091 w/Bushhog QT2345 Loader & 6' Squealer Bushhog
Circle of Safety: Y
Location: TN, Lebanon

Re: 22 sickle bar Broken

Postby BIGHOSS » Fri Sep 02, 2011 4:25 pm

Pretty hard to weld the tube to the hanger because of the bronze bushing inside the tube. The heat will melt the expensive bushing. What I did was make a set screw with a jamb nut on the belt adjuster to hold the tube tight to the pulley shield. This keeps it in place and also keeps the tube from rotating. It is working well for me.
We make a living by what we get, but we make a life by what we give......Winston Churchill

Jim Becker
Team Cub
Team Cub
501 Club
501 Club
Posts: 12164
Joined: Sun Feb 02, 2003 2:59 pm
Zip Code: 55319
Circle of Safety: Y
Location: MN

Re: 22 sickle bar Broken

Postby Jim Becker » Fri Sep 02, 2011 6:32 pm

BIGHOSS wrote:Pretty hard to weld the tube to the hanger because of the bronze bushing inside the tube. The heat will melt the expensive bushing.

Good point. Another option is to pull the bushing while welding then reinstall it. It would be a good idea to look at the wear on the bushing before starting. There may be some benefit to turning it 90 degrees when reinstalling it.

oneofthesedays
5+ Years
5+ Years
Posts: 14
Joined: Mon Jun 20, 2011 11:37 pm
Zip Code: 01430
Tractors Owned: Farmall Cub - 1950?
cultivator, planter, 1 bottom plow
Farmall 100 - 1956
2 bottom plow, disc harrow, 22 sickle bar, snow plow
Location: Ashburnham MA

Re: 22 sickle bar Broken

Postby oneofthesedays » Fri Sep 02, 2011 6:55 pm

I am going to replace that bushing mine is worn down, problem is the shaft is worn on that end also. I am going to make a up a split bushing out of oil-lite bronze as the pully end of the shaft is larger than the pitman end. I will need to slide the shaft in almost all the way then push in the split bushing in the tube.

User avatar
Don McCombs
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 12114
Joined: Mon Feb 03, 2003 6:45 am
Zip Code: 21550
Tractors Owned: "1950 Something" Farmall Cub
1957 Farmall Cub w/FH
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A
1951 Farmall Super C w/FH
Circle of Safety: Y
Location: MD, Deep Creek Lake

Re: 22 sickle bar Broken

Postby Don McCombs » Fri Sep 02, 2011 7:04 pm

Original paint and decals on mine. All red, except for the pitman and grass rod assembly. Those are cream.

Image
Don McCombs
MD, Deep Creek Lake

Image
Proud Member of Maryland Chapter 39

User avatar
Bus Driver
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 2901
Joined: Sat Feb 11, 2006 5:26 pm
Location: NC

Re: 22 sickle bar Broken

Postby Bus Driver » Sat Sep 03, 2011 7:30 am

I suggest disassembling the mower for inspection and repair/replacement of every damaged part. Welding is easier when access is better and positioning is possible. For that weld, I doubt that the bushing will be damaged. Copper plates are used to back up the weld area on sheet metal repairs when MIG welding rust perforated areas. Copper and it's alloys wick heat away rapidly. I would weld the broken part with 7018 electrodes, not MIG. Contrary to conventional practice, I would consider leaving all the existing weld to aid in proper alignment, tack the parts thoroughly (6011 electrode is good for this) , and then grind limited portions and weld there before grinding the opposite area and welding it .
I built up the badly worn pulley end of the mower tube with MIG and ground it back to shape with no damage to the bushing.
Luck favors those who are prepared

User avatar
BIGHOSS
10+ Years
10+ Years
501 Club
501 Club
Posts: 1542
Joined: Tue Jul 18, 2006 9:55 pm
Zip Code: 37087
Tractors Owned: 1947 Cub S/N 9216
w/ C-22 Mower

1974 Cub S/N 244814
w/59 Woods Mower

Ford 3000 Gas S/N C375091 w/Bushhog QT2345 Loader & 6' Squealer Bushhog
Circle of Safety: Y
Location: TN, Lebanon

Re: 22 sickle bar Broken

Postby BIGHOSS » Sat Sep 03, 2011 10:04 am

I learned to weld many moons ago with 6010 DC and 6011 AC rods. But, after burning a few 7014 rods, It became my rod of choice. 7014 is not a low hydrogen rod as the 7018. A little moisture in a 7014 does not hurt the welding. 7018 needs to be kept very dry. Just MHO.
We make a living by what we get, but we make a life by what we give......Winston Churchill

User avatar
Rudi
Cub Pro
Cub Pro
501 Club
501 Club
Posts: 28707
Joined: Sun Feb 02, 2003 8:37 pm
Zip Code: E1A7J3
eBay ID: ve9rhs
Skype Name: R.H. "Rudi" Saueracker, SSM
Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger
Circle of Safety: Y
Twitter ID: Rudi Saueracker, SSM
Location: NB Dieppe, Canada

Re: 22 sickle bar Broken

Postby Rudi » Mon Sep 05, 2011 8:15 am

I used to prefer 6011's because that is what I learned on with Dad. Now after my course I have become a little wiser/accustomed to different rods and different types of welding. 7014's are now my rod of choice. Lots of metal gets laid on rather quick and good flow. I keep my rods in the plastic sealed rod keepers. My
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship


oneofthesedays
5+ Years
5+ Years
Posts: 14
Joined: Mon Jun 20, 2011 11:37 pm
Zip Code: 01430
Tractors Owned: Farmall Cub - 1950?
cultivator, planter, 1 bottom plow
Farmall 100 - 1956
2 bottom plow, disc harrow, 22 sickle bar, snow plow
Location: Ashburnham MA

Re: 22 sickle bar Broken

Postby oneofthesedays » Tue Sep 06, 2011 11:32 pm

What type of wood do you make a new pitman arm out of ?


Return to “Other Tractors and Machinery”

Who is online

Users browsing this forum: No registered users and 0 guests